u-boot.git/board/nvidia, branch v2015.07-rc2

ARM: tegra: move NVIDIA common files to arch/arm/mach-tegra

2015-05-13T16:46:19Z

All the Tegra boards borrow the files from board/nvidia/common/ directory, i.e., board/nvidia/common/* are not vendor-common files, but SoC-common files. Move NVIDIA common files to arch/arm/mach-tegra/ to clean up Makefiles. As arch/arm/mach-tegra/board.c already exists, this commit renames board/nvidia/common/board.c to arch/arm/mach-tegra/board2.c, expecting they will be consolidated as a second step. Signed-off-by: Masahiro Yamada Acked-by: Marcel Ziswiler Cc: Stephen Warren Cc: Tom Warren Cc: Simon Glass Acked-by: Simon Glass Signed-off-by: Tom Warren

tegra: nyan-big: Add LCD PMIC init and board ID

2015-05-13T16:24:08Z

Add required setup for the LCD display, and a function to provide the board ID. This requires GPIOs to be available prior to relocation. Signed-off-by: Simon Glass Signed-off-by: Tom Warren

tegra: Add support for setting up a as3722 PMIC

2015-05-13T16:24:08Z

Add support for this PMIC which is used on some Tegra124 boards. Signed-off-by: Simon Glass Signed-off-by: Tom Warren

tegra: Provide a function to allow LCD PMIC setup

2015-05-13T16:24:08Z

Some LCDs require a PMIC to be set up - add a function for this. Signed-off-by: Simon Glass Signed-off-by: Tom Warren

tegra: Add a board ID function

2015-05-13T16:24:07Z

Add a way of displaying a numeric board ID on start-up. Signed-off-by: Simon Glass Signed-off-by: Tom Warren

tegra: Move checkboard() into the board code

2015-05-13T16:24:07Z

This is only used by Nvidia boards, so move it into nvidia/common to simplify things. Signed-off-by: Simon Glass Signed-off-by: Tom Warren

tegra: seaboard: Correct the gpio_request() call

2015-03-30T16:59:58Z

Requesting a GPIO without a name is not supposed anymore. This causes the request to fail. Add a name so that the serial console works on seaboard. Signed-off-by: Simon Glass Reported-by: Stephen Warren Signed-off-by: Tom Warren

Merge branch 'master' of git://git.denx.de/u-boot-tegra

2015-03-10T23:09:18Z

Conflicts: README Signed-off-by: Tom Rini

dm: tegra: Enable driver model in SPL and adjust the GPIO driver

2015-03-04T19:55:04Z

Use the full driver model GPIO and serial drivers in SPL now that these are supported. Since device tree is not available they will use platform data. Remove the special SPL GPIO function as it is no longer needed. This is all in one commit to maintain bisectability. Signed-off-by: Simon Glass

ARM: tegra: import latest Jetson TK1 pinmux

2015-03-04T17:08:58Z

Syseng has revamped the Jetson TK1 pinmux spreadsheet, basing the content completely on correct configuration for the board/schematic, rather than the previous version which was based on the bare minimum changes relative to another reference board. The new spreadsheet sets TRISTATE for any input-only pins. This only works correctly if the global CLAMP bit is not set, so the Jetson TK1 board code has been adjusted accordingly. Apparently syseng have changed their mind since the previous advice that this needed to be set:-/ This content comes from Jetson_TK1_customer_pinmux.xlsm (v09) downloaded from https://developer.nvidia.com/hardware-design-and-development. Signed-off-by: Stephen Warren Signed-off-by: Tom Warren