u-boot.git/board/nvidia, branch v2020.07

common: Drop linux/bitops.h from common header

2020-05-19T01:19:23+00:00

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass

common: Drop linux/delay.h from common header

2020-05-19T01:19:23+00:00

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass

common: Drop log.h from common header

2020-05-19T01:19:18+00:00

Move this header out of the common header.

Signed-off-by: Simon Glass

common: Drop net.h from common header

2020-05-18T21:33:31+00:00

Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.

Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.

Signed-off-by: Simon Glass

ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support

2020-04-02T21:30:02+00:00

The Jetson Nano Developer Kit is a Tegra X1-based development board. It
is similar to Jetson TX1 but it is not pin compatible. It features 4GB
of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot
used for storage.

HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0
and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI
Ethernet controller provides onboard network connectivity. NVMe support
has also been added. Env save is at the end of QSPI (4MB-8K).

A 40-pin header on the board can be used to extend the capabilities and
exposed interfaces of the Jetson Nano.

Signed-off-by: Thierry Reding 
Signed-off-by: Tom Warren 
Tested-by: Peter Robinson

t210: pinmux: Remove pinmux/GPIO init from T210 boards

2020-04-02T21:30:01+00:00

T210 CBoot is now doing the full pinmux and GPIO init, based on the DTB
tables. Remove pinmux/GPIO init tables & code from all T210-based builds
below:

p2371-2180 aka TX1
p2371-0000
e2220-1170
p2571

Signed-off-by: Tom Warren 
Acked-by: Stephen Warren

env: Drop environment.h header file where not needed

2019-08-11T20:43:41+00:00

This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.

Acked-by: Joe Hershberger 
Signed-off-by: Simon Glass

env: Move env_get() to env.h

2019-08-11T20:43:41+00:00

Move env_get() over to the new header file.

Acked-by: Joe Hershberger 
Signed-off-by: Simon Glass

p2771-0000: Add support for framebuffer carveouts

2019-06-05T16:16:35+00:00

If early firmware initialized the display hardware and the display
controllers are scanning out a framebuffer (e.g. a splash screen), make
sure to pass information about the memory location of that framebuffer
to the kernel before booting to avoid the kernel from using that memory
for the buddy allocator.

This same mechanism can also be used in the kernel to set up early SMMU
mappings and avoid SMMU faults caused by the display controller reading
from memory for which it has no mapping.

Reviewed-by: Simon Glass 
Signed-off-by: Thierry Reding 
Signed-off-by: Tom Warren

p2371-2180: Add support for framebuffer carveouts

2019-06-05T16:16:35+00:00

If early firmware initialized the display hardware and the display
controllers are scanning out a framebuffer (e.g. a splash screen), make
sure to pass information about the memory location of that framebuffer
to the kernel before booting to avoid the kernel from using that memory
for the buddy allocator.

This same mechanism can also be used in the kernel to set up early SMMU
mappings and avoid SMMU faults caused by the display controller reading
from memory for which it has no mapping.

Reviewed-by: Simon Glass 
Signed-off-by: Thierry Reding 
Signed-off-by: Tom Warren