u-boot.git/board/omap3, branch v2009.08

omap3: replace all instances of gpmc config struct by one global

2009-08-08T09:34:11Z

Signed-off-by: Matthias Ludwig Signed-off-by: Dirk Behme

omap3: remove typedefs for configuration structs

2009-08-08T09:33:23Z

Signed-off-by: Matthias Ludwig Signed-off-by: Dirk Behme

omap3: embedd gpmc_cs into gpmc config struct

2009-08-07T21:31:51Z

Embedd chip select configuration into struct for gpmc config instead of having it completely separated as suggested by Wolfgang Denk on http://lists.denx.de/pipermail/u-boot/2009-May/052247.html Signed-off-by: Matthias Ludwig

OMAP3 Move twl4030 power and led functions

2009-07-29T07:57:30Z

Because twl4030 now has its own device files, move exiting omap3 power_init_r to a new location. power_init_r is the only function in board/omap3/common. It initializes the twl4030 power for the board and enables the led. The power part of the the function is moved to twl4030_power_init in drivers/power/twl4030.c The power compilation is conditional on the existing config variable CONFIG_TWL4030_POWER. The led part is moved to twl4030_led_init in the new file drivers/misc/twl4030_led.c The led compilation is conditional on the new config variable CONFIG_TWL4030_LED The directory board/omap3/common was removed because power_init_r was the only function in it. Signed-off-by: Tom Rix Acked-by: Jean-Christophe PLAGNIOL-VILLARD Acked-by: Heiko Schocher

TWL4030 Add power reset button

2009-07-28T06:56:31Z

The Zoom2 power reset button is on the top right side of the main board. Press and hold for about to 8 seconds to completely reset the board. Some of the beta boards have a hardware problem that prevents using this feature. If is difficult to further characterize the boards that fail. So disable resetting for all beta boards. The Zoom1 reset button is the red circle on the top right, front of the board. Press and hold the button for 8 seconds to completely reset the board. After analyzing beagle, it was determined that other boards that use the twl4030 for power managment can also make use this function. The resetting is done by the power management part of the twl4030. Since there is no existing drivers/power, add one. The compilation of power/twl4030.h is controlled by the config variable CONFIG_TWL4030_POWER Signed-off-by: Tom Rix Acked-by: Jean-Christophe PLAGNIOL-VILLARD Acked-by: Heiko Schocher

Convert SMC911X Ethernet driver to CONFIG_NET_MULTI API

2009-07-23T05:53:44Z

All in-tree boards that use this controller have CONFIG_NET_MULTI added Also: - changed CONFIG_DRIVER_SMC911X* to CONFIG_SMC911X* - cleaned up line lengths - modified all boards that override weak function in this driver - added Signed-off-by: Ben Warren Tested-by: Mike Frysinger

OMAP3 pandora: Fix CKE1 MUX setting to allow self-refresh

2009-07-12T15:43:29Z

Pandora is using both SDRC CSes. The MUX setting is needed for the second CS clock signal to allow the 2 RAM parts to be put in self-refresh correctly. Based on similar patch for beagle and overo by Jean Pihet and Steve Sakoman.

OMAP3 pandora: setup pulls for various GPIOs

2009-07-12T15:43:28Z

Set pullups or pulldowns for GPIOs which need them. Disable them for others, which have external pulls. Also make disabled pull setting consistent (some pins had type set to "up" even if pull type selection was disabled).

OMAP3 pandora: setup pin mux for pins used on rev3 boards

2009-07-12T15:43:26Z

Setup pin mux for GPIO pins connected on rev3 or later boards. Also change NUB2 IRQ pin. This should not affect older boards because they don't have any nubs (analog controllers) attached to them.

OMAP3 pandora: pin mux cleanup

2009-07-12T15:43:24Z

Remove configuration of not unused pins, effectively leaving them in safe mode.