u-boot.git/board/phytec, branch v2017.09-rc3

Merge git://www.denx.de/git/u-boot-imx

2017-08-16T22:12:00Z

Update pfla02 for setenv changes and PHYLIB/etc migration to Kconfig. Signed-off-by: Tom Rini

env: Rename eth_getenv_enetaddr() to eth_env_get_enetaddr()

2017-08-16T12:30:44Z

Rename this function for consistency with env_get(). Signed-off-by: Simon Glass

env: Rename eth_setenv_enetaddr() to eth_env_set_enetaddr()

2017-08-16T12:23:56Z

Rename this function for consistency with env_set(). Signed-off-by: Simon Glass

mx6: Add support for Phytec pfla02 (NAND)

2017-08-02T09:45:27Z

Add support for Phytec pfla02, equipped with NAND. CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 31C Reset cause: POR I2C: ready DRAM: 1 GiB NAND: 2048 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 SF: Detected n25q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 0 Signed-off-by: Stefano Babic CC: Stefan Christ CC: Stefan Müller-Klieser CC: Christian Hemp

imx: reorganize IMX code as other SOCs

2017-07-12T08:17:44Z

Change is consistent with other SOCs and it is in preparation for adding SOMs. SOC's related files are moved from cpu/ to mach-imx/. This change is also coherent with the structure in kernel. Signed-off-by: Stefano Babic CC: Fabio Estevam CC: Akshay Bhat CC: Ken Lin CC: Marek Vasut CC: Heiko Schocher CC: "Sébastien Szymanski" CC: Christian Gmeiner CC: Stefan Roese CC: Patrick Bruenn CC: Troy Kisky CC: Nikita Kiryanov CC: Otavio Salvador CC: "Eric Bénard" CC: Jagan Teki CC: Ye Li CC: Peng Fan CC: Adrian Alonso CC: Alison Wang CC: Tim Harvey CC: Martin Donnelly CC: Marcin Niestroj CC: Lukasz Majewski CC: Adam Ford CC: "Albert ARIBAUD (3ADEV)" CC: Boris Brezillon CC: Soeren Moch CC: Richard Hu CC: Wig Cheng CC: Vanessa Maegima CC: Max Krummenacher CC: Stefan Agner CC: Markus Niebel CC: Breno Lima CC: Francesco Montefoschi CC: Jaehoon Chung CC: Scott Wood CC: Joe Hershberger CC: Anatolij Gustschin CC: Simon Glass CC: "Andrew F. Davis" CC: "Łukasz Majewski" CC: Patrice Chotard CC: Nobuhiro Iwamatsu CC: Hans de Goede CC: Masahiro Yamada CC: Stephen Warren CC: Andre Przywara CC: "Álvaro Fernández Rojas" CC: York Sun CC: Xiaoliang Yang CC: Chen-Yu Tsai CC: George McCollister CC: Sven Ebenfeld CC: Filip Brozovic CC: Petr Kulhavy CC: Eric Nelson CC: Bai Ping CC: Anson Huang CC: Sanchayan Maity CC: Lokesh Vutla CC: Patrick Delaunay CC: Gary Bisson CC: Alexander Graf CC: u-boot@lists.denx.de Reviewed-by: Fabio Estevam Reviewed-by: Christian Gmeiner

rockchip: Add basic support for phyCORE-RK3288 SoM based carrier board

2017-07-11T13:23:38Z

The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC. The module can be connected to different carrier boards. It can be also equipped with different RAM, SPI flash and eMMC variants. The Rapid Development Kit option is using the following setup: - 1 GB DDR3 RAM (2 Banks) - 1x 4 KB EEPROM - DP83867 Gigabit Ethernet PHY - 16 MB SPI Flash - 4 GB eMMC Flash Add basic support for the PCM-947 carrier board, a RK3288 based development board made by PHYTEC. This board works in a combination with the phyCORE-RK3288 System on Module. Signed-off-by: Wadim Egorov Reviewed-by: Simon Glass Acked-by: Philipp Tomsich

powerpc, 5xxx, 512x: remove support for mpc5xxx and mpc512x

2017-06-16T14:14:55Z

There was for long time no activity in the mpx5xxx area. We need to go further and convert to Kconfig, but it turned out, nobody is interested anymore in mpc5xxx, so remove it. Signed-off-by: Heiko Schocher

Kconfig: Add a CONFIG_IDE option

2017-05-22T16:45:27Z

At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate CONFIG_IDE option so that IDE support can be enabled without requiring the 'ide' command. Update existing users and move the ide driver into drivers/block since it should not be in common/. Signed-off-by: Simon Glass

pcm058: Fix unused variable warnings

2017-05-12T12:37:27Z

The variable nfc_pads is only referenced when CONFIG_CMD_NAND is set, add a gaurd. The variable gpio_pads is never referenced, drop it. The variable usdhc4_pads are only referenced when we do not have CONFIG_CMD_NAND set and we are not doing an SPL build, modify the existing guard. Cc: Stefano Babic Signed-off-by: Tom Rini Reviewed-by: Stefano Babic

board_f: Rename initdram() to dram_init()

2017-04-13T13:40:57Z

This allows us to use the same DRAM init function on all archs. Add a dummy function for arc, which does not use DRAM init here. Signed-off-by: Simon Glass [trini: Dummy function on nios2] Signed-off-by: Tom Rini