u-boot.git/board/samsung/common/Makefile, branch master

board: Use CONFIG_XPL_BUILD instead of CONFIG_SPL_BUILD

2024-10-11T17:44:48Z

Use the new symbol to refer to any 'SPL' build, including TPL and VPL Signed-off-by: Simon Glass

samsung: exynos: Convert SROMC interface to a driver

2021-07-27T01:34:27Z

Add a bus driver for this and use it to configure the bus parameters for the Ethernet interface. Drop the old pre-driver-model code. Switch over to use driver model for Ethernet. Signed-off-by: Simon Glass Reviewed-by: Jaehoon Chung Signed-off-by: Minkyu Kang

SPDX: Convert all of our single license tags to Linux Kernel style

2018-05-07T13:34:12Z

When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini

i2c: Drop CONFIG_SOFT_I2C_MULTI_BUS

2017-04-05T17:55:11Z

This is not used by any board. Drop it. Signed-off-by: Simon Glass Clean up board_f sequence a little This series tries to remove #ifdefs from the board_f init sequence. It gets as far as I2C and then we need to discuss whether we can start to remove the old I2C framework. I think that ideally each entry in the init sequence should be enabled by at most one CONFIG, which is in Kconfig and is not arch-specific. END Acked-by: Lukasz Majewski Acked-by: Jaehoon Chung

exynos5-dt-types: add board detection for Odroid XU3/XU3L/XU4.

2015-11-02T01:38:00Z

This commit adds additional file with implementation of board detection code for Odroid-XU3/XU4. The detection depends on compatible found in fdt: - "samsung,exynos5" - uses Exynos5 generic code - "samsung,odroidxu3" - try detect XU3 revision There are few revisions of Odroid XU3/XU4, each can be detected by checking the value of channel 9 of built-in ADC: Rev ADC Board 0.1 0 XU3 0.1 0.2 372 XU3 0.2 | XU3L - no DISPLAYPORT 0.3 1280 XU4 0.1 The detection code depends on the ADC+10% value. Implementation of functions: - set_board_type() - read ADC and set type - get_board_rev() - returns board revision: 1..3 - get_board_type() - returns board type string Additional functions with return values of bool: - board_is_generic() - true if found compatible "samsung,exynos5" but not "samsung,odroidxu3" - board_is_odroidxu3() - true if found compatible "samsung,odroidxu3" and one of XU3 revision. - board_is_odroidxu4() - true if found compatible "samsung,odroidxu3" and XU4 revision. After I2C controller init, the get_board_type() can check if the XU3 board is a "Lite" variant, by probing chip 0x40 on I2C0 (INA231 - exists only on non-lite). This is useful for setting fdt file name at misc_init_r(). Enabled configs: - CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG - CONFIG_ODROID_REV_AIN - CONFIG_REVISION_TAG - CONFIG_BOARD_TYPES Signed-off-by: Przemyslaw Marczak Cc: Minkyu Kang Cc: Simon Glass Tested-by: Anand Moon Signed-off-by: Minkyu Kang

exynos: Add common board code for exynos5 boards that use device tree

2015-08-06T03:06:15Z

Some boards use device tree for almost all board-specific configuration. They therefore do not need their own separate board code, but can all use the same version. Add a common version of the board code. It uses the PMIC, regulator and video bridge uclasses. This will support smdk5250, smdk5420, snow, spring, pit and pi. Signed-off-by: Simon Glass

usb: USB download gadget and functions config options coherent naming

2015-07-22T06:57:53Z

This introduces a coherent scheme for naming USB download gadget and functions config options. The download USB gadget config option is moved to CONFIG_USB_GADGET_DOWNLOAD for better consistency with other gadgets and each function's config option is moved to a CONFIG_USB_FUNCTION_ prefix. Signed-off-by: Paul Kocialkowski Tested-by: Lukasz Majewski Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)

samsung: dfu: Provide correct Vendor and Product IDs for UMS gadget

2014-08-20T11:10:32Z

It is necessary to provide the same Vendor and Product IDs as the one in the original Linux kernel code. Without this change the USB mass storage gadget is not working with Windows7. Signed-off-by: Lukasz Majewski Acked-by: Minkyu Kang

ums: move IO support code to common location

2014-05-08T08:38:29Z

There's nothing Samsung-/board-specfic about the implementation of ums_init(). Move the code into cmd_usb_mass_storage.c, so that it can be shared by any user of that command. Cc: Lukasz Majewski Signed-off-by: Stephen Warren Acked-by: Przemyslaw Marczak

samsung: common: Add file for common functions, draw_logo() cleanup.

2014-02-03T06:36:14Z

Changes: new file: - board/samsung/common/misc.c depends on: CONFIG_MISC_COMMON - move draw_logo() to misc.c configs: trats, trats2, universal: - enable CONFIG_MISC_COMMON, - enable CONFIG_MISC_INIT_R, - add misc_init_r() and call draw_logo() in it. Signed-off-by: Przemyslaw Marczak Signed-off-by: Minkyu Kang