u-boot.git/board/sbc8349, branch v2009.08

sbc8349: combine HRCW flash and u-boot image flash

2009-07-27T23:35:53Z

Up to this point in time, the sbc8349 board was storing the u-boot image in flash 2x. One for the HRCW value at the beginning of flash (0xff80_0000), and once close to the end of flash (0xfff8_0000) for the actual image that got executed. This moves the TEXT_BASE to be the beginning of flash, which makes the second copy of the image redundant, and frees up the flash from the end of the environment storage to the end of the flash device itself. Signed-off-by: Paul Gortmaker Signed-off-by: Kim Phillips

mpc83xx: convert all remaining boards over to 83XX_GENERIC_PCI

2009-07-19T00:43:04Z

Signed-off-by: Kim Phillips

83xx: Replace CONFIG_MPC83XX with CONFIG_MPC83xx

2009-06-12T18:47:17Z

Use the standard lowercase "xx" capitalization that other Freescale architectures use for CPU defines to prevent confusion and errors Signed-off-by: Peter Tyser Signed-off-by: Kim Phillips

pci: Rename PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY for clarity

2009-02-07T22:50:04Z

The PCI_REGION_MEMORY and PCI_REGION_MEM are a bit to similar and can be confusing when reading the code. Rename PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY to clarify its used for system memory mapping purposes. Signed-off-by: Kumar Gala

Make Freescale local bus registers available for both 83xx and 85xx.

2008-10-29T16:12:53Z

- Rename lbus83xx_t to fsl_lbus_t and move it to asm/fsl_lbc.h so that it can be shared by both 83xx and 85xx - Remove lbus83xx_t and replace it with fsl_lbus_t in all 83xx boards files which use lbus83xx_t. - Move FMR, FIR, FCR, FPAR, LTESR from mpc83xx.h to asm/fsl_lbc.h so that 85xx can share them. Signed-off-by: Jason Jin Signed-off-by: Haiying Wang Signed-off-by: Scott Wood

rename CFG_ macros to CONFIG_SYS

2008-10-18T19:54:03Z

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

mpc83xx: spd_sdram: fix ddr sdram base address assignment bug

2008-09-24T14:58:33Z

The spd_dram code shifts the base address, then masks 20 bits, but forgets to shift the base address back. Fix this by just masking the base address correctly. Found this bug while trying to relocate a DDR memory at the base != 0. Signed-off-by: Anton Vorontsov Signed-off-by: Kim Phillips

Cleanup out-or-tree building for some boards (.depend)

2008-07-02T21:49:18Z

Signed-off-by: Wolfgang Denk

Change initdram() return type to phys_size_t

2008-06-12T06:50:18Z

This patch changes the return type of initdram() from long int to phys_size_t. This is required for a couple of reasons: long int limits the amount of dram to 2GB, and u-boot in general is moving over to phys_size_t to represent the size of physical memory. phys_size_t is defined as an unsigned long on almost all current platforms. This patch *only* changes the return type of the initdram function (in include/common.h, as well as in each board's implementation of initdram). It does not actually modify the code inside the function on any of the platforms; platforms which wish to support more than 2GB of DRAM will need to modify their initdram() function code. Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc MPC8641HPCN. Signed-off-by: Becky Bruce

Remove erroneous or extra spd.h #includers.

2008-03-04T23:17:43Z

Many of the spd.h #includers don't need it, and wanted to have spd_sdram() declared instead. Since they didn't get that, some also had open coded extern declarations of it instead or as well. Fix it all up by using spd_sdram.h where needed. Signed-off-by: Jon Loeliger