u-boot.git/board/solidrun, branch v2023.10

MAINTAINERS: Fix path typos and similar

2023-07-25T16:44:47Z

We have a number of cases where the in-tree path of files and where they presumably were when the first version of a patch were posted differ slightly. Correct these to point at where the files are now. Signed-off-by: Tom Rini Reviewed-by: Simon Glass

MAINTAINERS: Add some missing defconfig files to existing entries

2023-07-25T16:44:47Z

We have a few places where defconfigs were added (or renamed) and not included in their previously listed MAINTAINERS entry, correct this. Signed-off-by: Tom Rini Acked-by: Adam Ford Reviewed-by: Simon Glass

solidrun: mx6cuboxi: use CONFIG_IS_ENABLED(SATA) instead of ifdef CONFIG_SATA

2023-05-10T20:45:42Z

Prepare for linking setup_sata only when CONFIG_SATA/CONFIG_SPL_SATA is defined. Signed-off-by: Troy Kisky Reviewed-by: Simon Glass

arm: mvebu: clearfog: Detect MMC vs SDHC and fixup fdt

2023-03-30T05:05:20Z

[upstream of vendor commit 19a96f7c40a8fc1d0a6546ac2418d966e5840a99] The Clearfog devices have only one SDHC device. This is either eMMC if it is populated on the SOM or SDHC if not. The Linux device tree assumes the SDHC case. Detect if the device is an eMMC and fixup the device-tree so it will be detected by Linux. Ported from vendor repo at https://github.com/SolidRun/u-boot Signed-off-by: Martin Rowe Reviewed-by: Stefan Roese

imx: Use SATA instead of CMD_SATA

2023-03-03T14:49:02Z

This causes a build failure on mx6cuboxi with split config, since CMD_SATA shows up as enabled in SPl (because there is no SPL_CMD_SATA). The condition is wrong anyway, so change it to use SATA instead. Signed-off-by: Simon Glass

global: Move remaining CONFIG_SYS_SDRAM_* to CFG_SYS_SDRAM_*

2022-12-05T21:06:07Z

The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM namespace do not easily transition to Kconfig. In many cases they likely should come from the device tree instead. Move these out of CONFIG namespace and in to CFG namespace. Signed-off-by: Tom Rini Reviewed-by: Simon Glass

mx6cuboxi: migrate to DM_SERIAL

2022-11-08T16:35:00Z

Add the needed DT overrides to enable UART in SPL. Cc: Fabio Estevam Signed-off-by: Baruch Siach Tested-by: Tom Rini Reviewed-by: Fabio Estevam

Makefile: Rename u-boot-spl.kwb to u-boot-with-spl.kwb

2022-11-07T06:17:55Z

File name with pattern u-boot-spl* is used on all places except in kwb image for binary with SPL-only code. Combined binary with both SPL and proper U-Boot in other places has file name pattern u-boot-with-spl*. Make it consistent also for kwb image and rename u-boot-spl.kwb to u-boot-with-spl.kwb as this image contains both SPL and proper U-Boot code. Also update documentation about file name changes. Signed-off-by: Pali Rohár Reviewed-by: Stefan Roese

mx6cuboxi: fix board detection while patching device-tree phy nodes

2022-07-25T13:08:23Z

ft_board_setup relies on the board_type() function to optimize which phy nodes need to be enabled for Linux. Add calls to setup and release the board-detect GPIOs. Also fix the switch-case statement to only enable phy address 4 for Cubox and unknown devices. Fixes: 741ce308 ("mx6cuboxi: fixup dtb ethernet phy nodes before booting an OS") Signed-off-by: Josua Mayer

mx6cuboxi: fixup dtb ethernet phy nodes before booting an OS

2022-06-14T19:25:26Z

SoM revision 1.9 has replaced the ar8035 phy address 0 with an adin1300 at address 1. Because early SoMs had a hardware flaw, the ar8035 can also appear at address 4 - making it a total of 3 phy nodes in the DTB. To avoid confusing Linux with probe errors, fixup the dtb to only enable the phy node that is detected at runtime. Signed-off-by: Josua Mayer