u-boot.git/board/st/common, branch v2020.07

command: Remove the cmd_tbl_t typedef

2020-05-18T22:36:55Z

We should not use typedefs in U-Boot. They cannot be used as forward declarations which means that header files must include the full header to access them. Drop the typedef and rename the struct to remove the _s suffix which is now not useful. This requires quite a few header-file additions. Signed-off-by: Simon Glass

part: Drop disk_partition_t typedef

2020-05-18T21:33:33Z

We should not be using typedefs and these make it harder to use forward declarations (to reduce header file inclusions). Drop the typedef. Signed-off-by: Simon Glass

stm32mp: stm32prog: adapt the MTD partitions

2020-05-14T07:02:12Z

Dynamically adapt the MTD partitions in NOR/NAND/SPI-NAND when stm32prog command detects in the parsed flash layout files: - a fsbl partition in NOR. - a tee partition in NOR/NAND/SPI-NAND Signed-off-by: Patrick Delaunay Reviewed-by: Patrice Chotard

stm32mp: add the command stm32prog

2020-05-14T07:02:12Z

Add a specific command stm32prog for STM32MP soc family witch allows to program the boot devices with the tool STM32CubeProgrammer (http://www.st.com/STM32CubeProg). This command uses the same UART STM32 protocol than MCU STM32 with or USB with DFU protocol v1.1 (ithe MCU ST extension are no supported). The executed actions are based on a tab separated value file with a stm32 header, the FlashLayout file (https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout). This file is parsed by the U-Boot command to: - initialize the devices - create the partition table on each device - initialize the DFU backend to access to not volatile memory (NOR/NAND/SD/eMMC) or to virtual device (OTP/PMIC) Up to STM32PROG_MAX_DEV (5) devices can be updated with a FlashLayout. The communication between U-Boot and STM32CubeProgrammer is done with the specific alternate configuration (see "AN5275: USB DFU/USART protocols used in STM32MP1 Series bootloaders" for details). The command stm32prog is executed when a boot from USB is detected (selected with bootpins) and we can program the boot devices with a simple command (on Windows or Linux): PC $> STM32_Programmer_CLI -c port=usb1 -w flaslayout.tsv 1/ the ROM code loads TF-A in embedded RAM (DFU or uart) 2/ TF-A loads flashlayout file and U-Boot in DDR (DFU or uart) 3/ U-Boot executes the stm32prog command (DFU or uart) Signed-off-by: Patrick Delaunay Reviewed-by: Patrice Chotard Reviewed-by: Patrice Chotard

board: stm32mp1: adapt MTD partition for BOOT from NOR or NAND

2020-05-14T07:02:12Z

Dynamically adapt the MTD partitions in NAND and SPI-NAND when boot from NOR or NAND/SPI-NAND is detected. This patch avoids to define the save MTD partition name for NOR and NAND devices and issue with latest kernel: only the needed MTD partitions are defined. For boot from NOR 1/ bootloader (TF-A, U-Boot and OP-TE) in NOR 2/ one large UBI partition in NAND For boot from NAND 1/ bootloader (TF-A, U-Boot and OP-TE) in MTD raw partition 2/ one large UBI partition Signed-off-by: Patrick Delaunay Reviewed-by: Patrice Chotard

stm32mp1: dynamically detect op-tee presence

2020-05-14T07:02:12Z

Activate OP-TEE driver for trusted and optee defconfig. This driver allows detection of TEE presence for boot from flash; CONFIG_STM32MP1_OPTEE is also removed. Signed-off-by: Patrick Delaunay Reviewed-by: Patrice Chotard

stm32mp1: move MTDPART configuration in Kconfig

2020-05-14T07:02:12Z

This patch reduces the stm32mp1 environment size and builds dynamically the MTD partitions with information from defconfig (CONFIG_MTDPARTS_...). Signed-off-by: Patrick Delaunay Reviewed-by: Patrice Chotard

stm32mp1: dynamically build DFU_ALT_INFO

2020-05-14T07:02:12Z

This patch reduces the stm32mp1 environment size and builds dynamically the DFU board configuration with gpt and mtd partitions and information from defconfig (CONFIG_DFU_ALT_RAM0). Signed-off-by: Patrick Delaunay Reviewed-by: Patrice Chotard

board: stm32mp1: move set_dfu_alt_info in st common directory

2020-05-14T07:02:12Z

Move the stm32mp1 common code set_dfu_alt_info() in common directory, this patch reduce the maintenance effort on this generic part (not board dependent). Signed-off-by: Patrick Delaunay Reviewed-by: Patrice Chotard

board: stm32mp1: move board_get_mtdparts in st common directory

2020-05-14T07:02:12Z

Move the stm32mp1 common code board_get_mtdparts() in common directory, this patch reduce the maintenance effort on this generic part (not board dependent). Signed-off-by: Patrick Delaunay Reviewed-by: Patrice Chotard