u-boot.git/board/st, branch v2018.07

stm32mp1: Allow to activate CONFIG_DEBUG_UART

2018-05-26T22:19:18Z

Add the needed information to enable the debug uart to have printf before the serial driver probe (so before probe for clock, pincontrol and reset drivers) To enable the debug on uart 4 (default console): + CONFIG_DEBUG_UART=y + CONFIG_DEBUG_UART_STM32=y Signed-off-by: Patrick Delaunay Signed-off-by: Patrice Chotard

SPDX: Convert all of our multiple license tags to Linux Kernel style

2018-05-07T14:24:31Z

When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have multiple licenses (in these cases, dual license) declared in the SPDX-License-Identifier tag. In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B" as per the Linux Kernel style document. Note that parenthesis are allowed so when they were used before we continue to use them. Reviewed-by: Fabio Estevam Signed-off-by: Tom Rini

SPDX: Convert all of our single license tags to Linux Kernel style

2018-05-07T13:34:12Z

When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini

stm32mp1: add eMMC support for ED1

2018-04-07T00:45:28Z

Add command GPT support Add EMMC boot support Add the 2 other SDMMC instances for ED1: - SDMMC2 = mmc 1, eMMC on the ED1 board - SDMMC3 = extension connector, deactivated by default Signed-off-by: Patrick Delaunay

board: st: add generic board for STM32MP1 family

2018-03-19T20:14:22Z

Add first support for STM32MP157C-ED1 board with "Basic" boot chain 1/ Boot Rom: load SPL with STM32 image header in SYSRAM 2/ SPL: power up and initialize the DDR and load U-Boot image from SDCARD in DDR 3/ U-Boot: search and load extlinux.conf in SDCARD (DISTRO activated) Signed-off-by: Patrick Delaunay

stm32f7: board: add splash screen

2018-03-19T10:01:04Z

Support several pixel format (8bits, 16bits, 24bits & 32bits). Add new file st_logo_data.h which contains logo stmicroelectronics_uboot_logo_8bit_rle.bmp. Signed-off-by: yannick fertre

arch-stm32: Remove stm32_periph.h

2018-03-14T01:45:37Z

Remove arch/arm/include/asm/arch-stm32fx/stm32_periph.h as all defines or enums are no more used. Signed-off-by: Patrice Chotard

board: stm32: switch to DM STM32 timer

2018-03-14T01:45:37Z

Use available DM stm32_timer driver instead of dedicated mach-stm32/stm32fx/timer.c. Remove all defines or files previously used for timer usage in arch/arm/include/asm/arch-stm32fx and in arch/arm/mach-stm32/stm32fx Enable DM STM32_TIMER for STM32F4/F7 and H7. Signed-off-by: Patrice Chotard

clk: clk_stm32f: Move SYSCFG clock setup into configure_clocks()

2018-01-28T14:39:15Z

Move SYSCFG clock setup into configure_clocks() instead of calling clock_setup() from board file. As this clock is only needed in case of ethernet enabled and as both stm32f4 and stm32f7 are using the Designware ethernet IP, we use CONFIG_ETH_DESIGNWARE to only enable this clock if needed. Move the RMII setup from board_early_init_f() to board_init() to insure that RMII bit is set only when clock driver is initialized. Signed-off-by: Patrice Chotard

clk: clk_stm32f: Remove STMMAC clock setup

2018-01-28T14:39:15Z

Thanks to 'commit ba1f96672522 ("net: designware: add clock support")' we don't need anymore to setup the STMMAC clock in board. Signed-off-by: Patrice Chotard Reviewed-by: Vikas Manocha