u-boot.git/board/st, branch v2018.09

stm32f7: board: Fix memory init

2018-08-13T18:03:57Z

Commit 1473b12ad0b3 ("lib: fdtdec: Update ram_base to store ram start adddress") brings regression on STM32F7 which can't boot. Use fdtdec_setup_mem_size_base() to setup memory base and size. Use fdtdec_setup_memory_banksize() to setup memory bank base and size. Reported-by: Mark Olsson Signed-off-by: Patrice Chotard Cc: Mark Olsson Reviewed-by: Vikas Manocha

board: stm32: use bi_dram[0].start instead of hardcoded value

2018-08-13T18:03:57Z

Use gd->bd->bi_dram[0].start initialized from DT instead of using hardcoded CONFIG_SYS_SDRAM_BASE from config file. Remove unused CONFIG_SYS_RAM_BASE and CONFIG_SYS_SDRAM_BASE defines. Signed-off-by: Patrice Chotard

stm32mp1: use new function led default state

2018-08-10T14:27:32Z

Initialize the led with the default state defined in device tree. Reviewed-by: Simon Glass Signed-off-by: Patrick Delaunay

stm32mp1: add support for stm32mp157c-ev1 board

2018-07-20T19:55:05Z

Add support of stm32mp157c-ev1, the evaluation board with pmic stpmu1 (ev1 = mother board + daughter ed1) with device tree. EV1 is the selected board by default in basic defconfig. PS: CONFIG_PINCTRL_FULL activation avoid to increase SYS_MALLOC_F_LEN (Early malloc usage: 2034) Signed-off-by: Patrick Delaunay

lib: fdtdec: Rename routine fdtdec_setup_memory_size()

2018-07-19T08:49:56Z

This patch renames the routine fdtdec_setup_memory_size() to fdtdec_setup_mem_size_base() as it now fills the mem base as well along with size. Signed-off-by: Siva Durga Prasad Paladugu Signed-off-by: Michal Simek Reviewed-by: Tom Rini

stm32mp1: Allow to activate CONFIG_DEBUG_UART

2018-05-26T22:19:18Z

Add the needed information to enable the debug uart to have printf before the serial driver probe (so before probe for clock, pincontrol and reset drivers) To enable the debug on uart 4 (default console): + CONFIG_DEBUG_UART=y + CONFIG_DEBUG_UART_STM32=y Signed-off-by: Patrick Delaunay Signed-off-by: Patrice Chotard

SPDX: Convert all of our multiple license tags to Linux Kernel style

2018-05-07T14:24:31Z

When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have multiple licenses (in these cases, dual license) declared in the SPDX-License-Identifier tag. In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B" as per the Linux Kernel style document. Note that parenthesis are allowed so when they were used before we continue to use them. Reviewed-by: Fabio Estevam Signed-off-by: Tom Rini

SPDX: Convert all of our single license tags to Linux Kernel style

2018-05-07T13:34:12Z

When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini

stm32mp1: add eMMC support for ED1

2018-04-07T00:45:28Z

Add command GPT support Add EMMC boot support Add the 2 other SDMMC instances for ED1: - SDMMC2 = mmc 1, eMMC on the ED1 board - SDMMC3 = extension connector, deactivated by default Signed-off-by: Patrick Delaunay

board: st: add generic board for STM32MP1 family

2018-03-19T20:14:22Z

Add first support for STM32MP157C-ED1 board with "Basic" boot chain 1/ Boot Rom: load SPL with STM32 image header in SYSRAM 2/ SPL: power up and initialize the DDR and load U-Boot image from SDCARD in DDR 3/ U-Boot: search and load extlinux.conf in SDCARD (DISTRO activated) Signed-off-by: Patrick Delaunay