u-boot.git/board/sunxi/gmac.c, branch main

Restore patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet"

2024-05-20T19:35:03Z

As part of bringing the master branch back in to next, we need to allow for all of these changes to exist here. Reported-by: Jonas Karlman Signed-off-by: Tom Rini

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

2024-05-19T14:16:36Z

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay Ethernet"' I failed to notice that b4 noticed it was based on next and so took that as the base commit and merged that part of next to master. This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35. Reported-by: Jonas Karlman Signed-off-by: Tom Rini

arm: sunxi: Remove and add needed includes

2024-05-06T21:06:33Z

Remove from all mach-sunxi and board/sunxi files and when needed add missing include files directly. Reviewed-by: Andre Przywara Signed-off-by: Tom Rini

sunxi: Remove non-DM GMAC pin setup

2022-04-04T22:24:16Z

This is now handled automatically by the pinctrl driver. Signed-off-by: Samuel Holland Reviewed-by: Andre Przywara Signed-off-by: Andre Przywara

sunxi: Clean up inclusions of asm/arch/gpio.h

2021-10-11T09:46:44Z

As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will remove the asm/arch/gpio.h header. In preparation, clean up the various files that include it. Some files did not contain any GPIO code at all, so this header was completely unused. A few files contained only legacy platform-specific GPIO code for setting up pin muxes. They were left unchanged, as that code will be completely removed by the DM_PINCTRL migration. The remaining files contain some combination of DM_GPIO and legacy GPIO code. For those, switch to including asm/gpio.h (if it wasn't included already). Right now, this header provides both sets of functions, because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the right header to include once the DM_GPIO migration is complete and GPIO_EXTRA_HEADER is no longer needed. Signed-off-by: Samuel Holland Reviewed-by: Andre Przywara Signed-off-by: Andre Przywara

board: sunxi: gmac: Remove Ethernet clock and reset

2019-04-16T10:59:01Z

Since Ethernet clock and reset is now handling via CLK and RESET frameworks via driver API's remove explicit ccm writes. Signed-off-by: Jagan Teki

sunxi: Fix A20-OLinuXino-MICRO LAN8710 support

2017-12-07T05:27:23Z

>From revision J the board uses new phy chip LAN8710. Compared with RTL8201, RA17 pin is TXERR. It has pullup which causes phy not to work. To fix this PA17 is muxed with GMAC function. This makes the pin output-low. Signed-off-by: Stefan Mavrodiev Acked-by: Maxime Ripard Reviewed-by: Jagan Teki

sunxi: Fix gmac not working due to cpu_eth_init no longer being called

2016-03-23T21:04:13Z

cpu_eth_init is no longer called for dm enabled eth drivers, this was causing the sunxi gmac eth controller to no longer work in u-boot. This commit fixes this by calling the clock, reset and pinmux setup function from s_init() and enabling the phy power pin (if any) from board_init(). The enabling of phy power cannot be done from s_init because it uses dm and dm is not ready yet at this point. Note that the mdelay is dropped as the phy gets enabled much earlier now, so it is no longer needed. Signed-off-by: Hans de Goede Acked-by: Ian Campbell Tested-by: Karsten Merker Tested-by: Michael Haas

sunxi: Introduce a hidden SUNXI_GEN_SUNxI Kconfig bool

2015-05-04T14:51:51Z

sun6i and newer (derived) SoCs such as the sun8i-a23, sun8i-a33 and sun9i have a various things in common, like having separate ahb reset control registers, the SID living inside the pmic, custom pmic busses, new style watchdog, etc. This commit introduces a new hidden SUNXI_GEN_SUN6I Kconfig bool which can be used to check for these features avoiding the need for an ever growing list of "#if defined CONFIG_MACH_SUN?I" conditionals as we add support for more "new style" sunxi SoCs. Note that this commit changes the behavior of the gmac and hdmi code for sun8i and the upcoming sun9i devices. This does not matter as sun8i does not have gmac nor hdmi, and sun9i has new hardware-blocks for these so the old code will not work there. Also this is intentional as if a sun8i / sun9i variant which does use the old hwblocks shows up then the GEN_SUN6I code paths will be the right ones to use. For completeness this also adds a SUNXI_GEN_SUN4I bool for A10/A13/A20. Signed-off-by: Hans de Goede Acked-by: Ian Campbell

dm: sunxi: Support driver model for Ethernet

2015-04-18T17:11:37Z

Adjust the Ethernet initialisation code to support driver model. It is no-longer necessary to call designware_initialize(). The device will be probed when it is used. The PHY type and GMAC base will come from the device tree. Signed-off-by: Simon Glass