u-boot.git/board/sunxi, branch v2016.11

sunxi: Add support for Cubieboard4

2016-10-30T10:38:05Z

The Cubieboard4 is an A80 SoC based development board from Cubietech. This board has a UART port, 4 USB host ports, a USB 3.0 OTG connector, HDMI and VGA outputs, a micro SD slot, 8G eMMC flash, 2G DRAM, a WiFi/BT combo chip, headphone and microphone jacks, IR receiver, and GPIO headers. Signed-off-by: Chen-Yu Tsai Acked-by: Hans de Goede Signed-off-by: Hans de Goede

sunxi: Enable SPL support for A80 Optimus board

2016-10-30T10:38:04Z

The A80 Optimus Board was launched with the Allwinner A80 SoC. It was jointly developed by Allwinner and Merrii. This board has a UART port, a JTAG connector, 2 USB host ports, a USB 3.0 OTG connector, an HDMI output, a micro SD slot, 16G eMMC flash, 2G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone jack, IR receiver, and additional GPIO headers. Signed-off-by: Chen-Yu Tsai [hdegoede@redhat.com: update existing Merrii_A80_Optimus_defconfig instead of adding a new defconfig] Acked-by: Hans de Goede Signed-off-by: Hans de Goede

sunxi: Add default zq value for sun9i (A80)

2016-10-30T10:38:04Z

Both the A80 Optimus board and the Cubieboard 4 use a zq value of 4145117, or 0x3f3fdd. Signed-off-by: Chen-Yu Tsai Acked-by: Hans de Goede Signed-off-by: Hans de Goede

sunxi: Set default CPU clock rate to 1008 MHz for sun9i (A80)

2016-10-30T10:38:04Z

In Allwinner's SDK the A80 is clocked to 1008 MHz by default. Signed-off-by: Chen-Yu Tsai Acked-by: Hans de Goede Signed-off-by: Hans de Goede

sunxi: add MMC pinmux setup for SDC2 on sun9i

2016-10-30T10:38:04Z

The A80 can support 8-bit eMMC with reset on the PC pingroups. Signed-off-by: Chen-Yu Tsai Acked-by: Hans de Goede Signed-off-by: Hans de Goede

sunxi: enable SPL for sun9i

2016-10-30T10:38:04Z

Now that DRAM initialization and clock setup is supported, we can enable SPL for the A80. [wens@csie.org: Added commit message] Signed-off-by: Chen-Yu Tsai Acked-by: Hans de Goede Signed-off-by: Hans de Goede

sunxi: DRAM initialisation for sun9i

2016-10-30T10:38:04Z

This adds DRAM initialisation code for sun9i, which calculates the appropriate timings based on timing information for the supplied DDR3 bin and the clock speeds used. With this DRAM setup, we have verified DDR3 clocks of up to 792MHz (i.e. DDR3-1600) on the A80-Q7 using a dual-channel configuration. [wens@csie.org: Moved dram_sun9i.c to arch/arm/mach-sunxi/; style cleanup] Signed-off-by: Chen-Yu Tsai [hdegoede@redhat.com: Drop some huge non-documenting #if 0 ... #endif blocks] [hdegoede@redhat.com: Fix checkpatch warnings] Signed-off-by: Hans de Goede

Convert CONSOLE_PRE_CONSOLE_BUFFER options to Kconfig

2016-10-23T22:33:19Z

Move these option to Kconfig and tidy up existing uses. Signed-off-by: Simon Glass Reviewed-by: Jagan Teki

Kconfig: Move config IDENT_STRING to Kconfig

2016-09-20T13:30:23Z

Move the config IDENT_STRING to Kconfig and migrate all boards [sivadur: Migrate zynq boards] Signed-off-by: Siva Durga Prasad Paladugu [trini: Update configs, add some default to sunxi Kconfig] Signed-off-by: Tom Rini

Merge branch 'master' of git://www.denx.de/git/u-boot-sunxi

2016-09-18T18:05:29Z