u-boot.git/board/sunxi, branch v2018.03

libfdt: move headers to and

2018-03-05T15:16:28Z

Thomas reported U-Boot failed to build host tools if libfdt-devel package is installed because tools include libfdt headers from /usr/include/ instead of using internal ones. This commit moves the header code: include/libfdt.h -> include/linux/libfdt.h include/libfdt_env.h -> include/linux/libfdt_env.h and replaces include directives: #include -> #include #include -> #include Reported-by: Thomas Petazzoni Signed-off-by: Masahiro Yamada

MAINTAINERS: Update email address for Maxime Ripard

2018-02-05T00:21:00Z

Free Electrons is no more and is now known as Bootlin, change my email address accordingly. Signed-off-by: Maxime Ripard

sunxi: Transition from the MMC to a FAT-based environment

2018-01-27T14:23:22Z

The current environment has been hardcoded to an offset that starts to be an issue given the current size of our main U-Boot binary. By implementing a custom environment location routine, we can always favor the FAT-based environment, and fallback to the MMC if we don't find something in the FAT partition. We also implement the same order when saving the environment, so that hopefully we can slowly migrate the users over to FAT-based environment and away from the raw MMC one. Eventually, and hopefully before we reach that limit again, we will have most of our users using that setup, and we'll be able to retire the raw environment, and gain more room for the U-Boot binary. Reviewed-by: Lukasz Majewski Signed-off-by: Maxime Ripard

sunxi: arm64: correct usage of DT node address in FIT generation

2018-01-16T01:29:21Z

The DT spec demands a unit-address in a node name to match the "reg" property in that node. Newer dtc versions will throw warnings if this is not the case. Adjust the FIT build script for 64-bit Allwinner boards to remove the bogus addresses from the node names and avoid the warnings. This avoids a warning with recent versions of the dtc tool. Signed-off-by: Andre Przywara

sunxi: maintainers: Add myself for the TBS A711

2018-01-10T06:00:49Z

Support for that board got introduced recently without the maintainers part. Let's fix that. Signed-off-by: Maxime Ripard Reviewed-by: Tom Rini Reviewed-by: Jagan Teki

sunxi: Add support for Libre Computer Board ALL-H3-CC H3 ver.

2018-01-10T05:57:41Z

The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry Pi B+ form factor single board computer based on the Allwinner H3 SoC. The board has 1GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes and connectors are in the exact same position as on the Raspberry Pi B+. Raspberry Pi B+ like peripherals supported on this board include: - Power input through micro-USB connector (without USB OTG) - Native 100 Mbps ethernet using the internal PHY, as opposed to USB-based on the RPi - 4x USB 2.0 host ports, directly connected to the SoC, as opposed to being connected through a USB 2.0 hub on the RPi - TV and audio output on a 3.5mm TRRS jack - HDMI output - Micro-SD card slot - Standard RPi B+ GPIO header, with the standard peripherals routed to the same pins. * 5V, 3.3V power, and ground * I2C0 on the H3 is routed to I2C1 pins on the RPi header * I2C1 on the H3 is routed to I2C0 pins on the RPi header * UART1 on the H3 is routed to UART0 pins on the RPi header * SPI0 on the H3 is routed to SPI0 pins on the RPi header, with GPIO pin PA17 replacing the missing Chip Select 1 * I2S1 on the H3 is routed to PCM pins on the RPi header - Additional peripherals from the H3 are available on different pins. These include I2S0, JTAG, PWM1, SPDIF, SPI1, and UART3 In addition, there are a number of new features: - Console UART header - Consumer IR receiver - Camera interface (not compatible with RPi) - Onboard microphone - eMMC expansion module port - Heatsink mounting holes This patch adds defconfig and dts files for this board. The dts file is the same as the one submitted for inclusion in Linux, with some minor revisions to match the dtsi file and old EMAC bindings in U-boot. Since the OTG controller is wired to a USB host port, and the H3 has proper USB hosts to handle host mode, the MUSB driver is not enabled. Signed-off-by: Chen-Yu Tsai Acked-by: Maxime Ripard Reviewed-by: Jagan Teki

sunxi: Fix A20-OLinuXino-MICRO LAN8710 support

2017-12-07T05:27:23Z

>From revision J the board uses new phy chip LAN8710. Compared with RTL8201, RA17 pin is TXERR. It has pullup which causes phy not to work. To fix this PA17 is muxed with GMAC function. This makes the pin output-low. Signed-off-by: Stefan Mavrodiev Acked-by: Maxime Ripard Reviewed-by: Jagan Teki

sun50i: h5: Add NanoPi Neo Plus2 DT initial support

2017-11-21T13:41:57Z

Add initial DT for NanoPi NEO Plus2 by FriendlyARM - Allwinner quad core H5 Cortex A53 with an ARM Mali-450MP GPU - 1 GB DDR3 RAM - 8GB eMMC flash (Samsung KLM8G1WEPD-B031) - micro SD card slot - Gigabit Ethernet (external RTL8211E-VB-CG chip) - 802.11 b/g/n WiFi, Bluetooth 4.0 (Ampak AP6212A module) - 2x USB 2.0 host ports Signed-off-by: Antony Antony Reviewed-by: Jagan Teki

sunxi: SATA link timeout fix

2017-11-10T13:51:24Z

After updating u-boot from v2016.01 to 2017.09, issue with "SATA link 0 timeout." on my Cubietruck board. mdelay milled after moving satapwr code to board. "sunxi: Turn satapwr on from board_init" (sha1: 9fbb0c3aa49f4604b0342cb527a6bd099f92eaeb) After adding the "mdelay(500);" line that was lost in the path the error is gone. Signed-off-by: Werner Böllmann [Rebased and updated change and commit message] Signed-off-by: Jagan Teki Reviewed-by: Jagan Teki

MAINTAINERS: Add missing boards and config entries

2017-11-06T14:58:51Z

As part of my usual round of build testing, output about missing MAINTAINERS information was not logged, and thus often overlooked. Correct that mistake by ensuring that I log the output of genboardscfg.py every time. As part of that, address a number of missing MAINTAINERS entires. In the case of a missing file, I have put the original submitter down. In the rest of the cases I have added the config (and sometimes relevant header file) to the existing set of file globs. Signed-off-by: Tom Rini