u-boot.git/board/ti/common, branch v2017.09

env: Rename eth_setenv_enetaddr() to eth_env_set_enetaddr()

2017-08-16T12:23:56Z

Rename this function for consistency with env_set(). Signed-off-by: Simon Glass

env: Rename setenv() to env_set()

2017-08-16T12:22:18Z

We are now using an env_ prefix for environment functions. Rename setenv() for consistency. Also add function comments in common.h. Suggested-by: Wolfgang Denk Signed-off-by: Simon Glass

env: Convert CONFIG_ENV_IS_IN... to a choice

2017-08-16T00:50:01Z

At present we support multiple environment drivers but there is not way to select between them at run time. Also settings related to the position and size of the environment area are global (i.e. apply to all locations). Until these limitations are removed we cannot really support more than one environment location. Adjust the location to be a choice so that only one can be selected. By default the environment is 'nowhere', meaning that the environment exists only in memory and cannot be saved. Also expand the help for the 'nowhere' option and move it to the top since it is the default. Signed-off-by: Simon Glass [trini: Move all of the imply logic to default X if Y so it works again] Signed-off-by: Tom Rini

ti: Default to ENV_IS_IN_FAT if MMC_OMAP_HS

2017-07-31T16:21:25Z

When we have MMC available we assume that we want to put the env as a file on FAT. Cc: Lokesh Vutla Signed-off-by: Tom Rini

ti: common: board_detect: Add function to determine if EEPROM was read

2017-07-10T18:25:53Z

When the EEPROM is first read its contents are stored in memory as a cache to avoid further I2C operations. To determine if the EEPROM was previously read the easiest way is to check the memory to see if the EEPROM's magic header value is set. Create a new function that can determine if the EEPROM was previously read or not without having to perform a I2C transaction. Signed-off-by: Franklin S Cooper Jr Reviewed-by: Tom Rini

ti: common: board_detect: Allow settings board detection variables manually

2017-07-10T17:45:35Z

In some situations the EEPROM used for board detection may not be programmed or simply programmed incorrectly. Therefore, it may be necessary to "simulate" reading the contents of the EEPROM to set appropriate variables used in the board detection code. This may also be helpful in certain boot modes where doing i2c reads may be costly and the config supports running only a specific board. Signed-off-by: Nishanth Menon Signed-off-by: Tero Kristo Signed-off-by: Keerthy Signed-off-by: Franklin S Cooper Jr. Reviewed-by: Tom Rini

board: ti: enable support for writing to fat partition

2017-06-03T21:55:19Z

Enable support for writing to FAT partitions on TI's boards. Signed-off-by: Sekhar Nori

Kconfig: Finish migration of hashing commands

2017-05-31T23:38:14Z

Currently these (board agnostic) commands cannot be selected using menuconfig and friends. Fix this the obvious way. As part of this, don't muddle the meaning of CONFIG_HASH_VERIFY to mean both 'hash -v' and "we have a hashing command" as this makes the Kconfig logic odd. Signed-off-by: Daniel Thompson [trini: Re-apply, add imply for a few cases, run moveconfig.py, also migrate CRC32_VERIFY] Signed-off-by: Tom Rini

Convert CONFIG_CMD_EEPROM et al to Kconfig

2017-05-22T13:33:49Z

This converts the following to Kconfig: CONFIG_CMD_EEPROM CONFIG_CMD_EEPROM_LAYOUT CONFIG_EEPROM_LAYOUT_HELP_STRING Signed-off-by: Simon Glass Reviewed-by: Tom Rini [trini: Rework Kconfig logic slightly, define EEPROM location on TI eval platforms] Signed-off-by: Tom Rini

ti: common: board_detect: Set alen to expected value before i2c read

2017-05-09T07:04:39Z

In non DM I2C read operations the address length passed in during a read operation will be used automatically. However, in DM I2C the address length is set to a default value of one which causes problems when trying to perform a read with a differing alen. Therefore, before the first read in a series of read operations set the alen to the correct value. Signed-off-by: Franklin S Cooper Jr Reviewed-by: Tom Rini Reviewed-by: Heiko Schocher