u-boot.git/board/ti, branch v2011.12

omap4_panda: Initialize the USB phy

2011-12-19T16:52:44Z

During misc_init_r, make sure to setup the clocks properly for the USB hub on the pandaboard. With this in place, the USB hub and the ethernet works on the pandaboard. Signed-off-by: Chris Lalancette Acked-by: Aneesh V

board/ti/omap2420h4/omap2420h4.c: Fix GC 4.6 build warning

2011-12-12T13:26:17Z

Fix: omap2420h4.c: In function 'dram_init': omap2420h4.c:196:25: warning: variable 'cpu' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk Cc: Richard Woodruff Cc: Tom Rini

board/ti/omap730p2/flash.c: Fix GCC 4.6 build warnings

2011-12-10T22:12:40Z

Fix: flash.c: In function 'flash_get_offsets': flash.c:122:10: warning: variable 'pOrgDef' set but not used [-Wunused-but-set-variable] flash.c: In function 'flash_erase': flash.c:263:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable] flash.c: In function 'write_data': flash.c:439:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk Cc: Dave Peverley Acked-by: Tom Rini

board/ti/omap1610inn/flash.c: Fix GCC 4.6 build warnings

2011-12-10T22:11:48Z

Fix: flash.c: In function 'flash_get_offsets': flash.c:139:10: warning: variable 'pOrgDef' set but not used [-Wunused-but-set-variable] flash.c: In function 'flash_erase': flash.c:280:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable] flash.c: In function 'write_data': flash.c:456:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk Acked-by: Tom Rini

AM3517 CraneBoard: Add SPL support

2011-12-06T22:59:39Z

The only change of note is that we move from 0x80008000 to 0x80100000 for CONFIG_SYS_TEXT_BASE Cc: Nagendra T S Tested-by: Koen Kooi Signed-off-by: Tom Rini

OMAP3: Add SPL support to omap3_evm

2011-12-06T22:59:38Z

Add Hynix 200MHz timing information to . This also changes CONFIG_SYS_TEXT_BASE to 0x80100000. Signed-off-by: Tom Rini

OMAP3: Add SPL support to Beagleboard

2011-12-06T22:59:38Z

This introduces 200MHz Micron parts timing information based on x-loader to and Numonyx MCFG calculation. The memory init logic is also based on what x-loader does in these cases. Note that while previously u-boot would be flashed in with SW ECC in this case it now must be flashed with HW ECC. We also change CONFIG_SYS_TEXT_BASE to 0x80100000. Cc: Dirk Behme Beagleboard rev C5, xM rev A: Tested-by: Tom Rini Beagleboard xM rev C: Tested-by: Matt Ranostay Beagleboard rev B7, C2, xM rev B: Tested-by: Matt Porter Signed-off-by: Tom Rini

AM3517: move AM3517 specific mux defines to generic header

2011-12-06T22:59:36Z

AM3517 specific CONTROL_PADCONF_* defines moved from board-specific files to Signed-off-by: Ilya Yanok

omap4460: fix TPS initialization

2011-12-06T22:59:34Z

TPS power IC is controlled using a GPIO (gpio_wk7). This GPIO should be maintained at logic 1 always. As such an internal pull-up on this pin will do the job, driving the GPIO outuput is not needed. This will avoid the need of using GPIO library in SPL and also may save some power. Signed-off-by: Aneesh V

omap4/5: Add support for booting with CH.

2011-11-15T21:25:50Z

Configuration header(CH) is 512 byte header attached to an OMAP boot image that will help ROM code to initialize clocks, SDRAM etc and copy U-Boot directly into SDRAM. CH can help us in by-passing SPL and directly boot U-boot, hence it's an alternative for SPL. However, we intend to support both CH and SPL for OMAP4/5. Initialization done through CH is limited and is not equivalent to that done by SPL. So U-Boot has to distinguish between the two cases and handle them accordingly. This patch takes care of doing this. Signed-off-by: sricharan Signed-off-by: Sandeep Paulraj