u-boot.git/board/ti, branch v2012.07

ARM: OMAP4: PANDA: Add rest of the USB module pads to essentials

2012-07-20T12:24:08Z

In commit 1a89a217f5c5ab3645c80c1247e8911a8b5ad491 we moved most of the required pads and mux data for USB to the essential list so that later on we could NOT enable anything that wasn't essential unless otherwise configured. This was however missing a few pandaboard-specific parts which left for example USB ethernet non-functional. Tested this on OMAP4430 ES2.2, OMAP4460 ES1.1 PANDA boards. (Reworded by Tom Rini to be more precise about what the problem was) Signed-off-by: R Sricharan Tested-by: Gary Thomas Tested-by: Tom Rini

beagle: add eeprom expansion board info for bct brettl4

2012-07-09T20:44:32Z

this is for a prototyping board vendor/product ids have been added to http://elinux.org/BeagleBoardPinMux#List_of_Vendor_and_Device_IDs Signed-off-by: Peter Meerwald

ARM: OMAP4/5: Move USB pads to essential list.

2012-07-07T12:07:36Z

USB module pads are getting enabled under non-essential group. These will be required for fastboot, tftp support. So move this to essential list to have them working when non-essential pads are no more muxed. Signed-off-by: R Sricharan

am33xx: Do not call init_timer twice

2012-07-07T12:07:21Z

We do not need to call init_timer both in SPL and U-Boot itself, just SPL needs to initialize the timer. Signed-off-by: Tom Rini

omap4: panda: disable uart2 pads during boot

2012-05-15T06:31:40Z

If uart2 is enabled during boot, spurious wifi chip transmission will hang the module and it is impossible to recover from this situation without hard reset. This will prevent any l4_per domain idle transitions. Signed-off-by: Tero Kristo

omap730p2: Remove empty misc_init_r

2012-05-15T06:31:27Z

We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R Signed-off-by: Tom Rini

omap5912osk: Remove empty misc_init_r

2012-05-15T06:31:27Z

We had a do-nothing misc_init_r, remove along with CONFIG_MISC_INIT_R Signed-off-by: Tom Rini

power: twl6035: add palmas PMIC support

2012-05-15T06:31:25Z

palmas/TWL6035 is power IC for omap5 evm boards Signed-off-by: Balaji T K

OMAP5: board: Add pinmux data for omap5_evm board.

2012-05-15T06:31:23Z

Adding the full pinmux data for OMAP5430 sevm board. Signed-off-by: R Sricharan

OMAP4460: TPS Ensure SET1 is selected after voltage configuration

2012-05-15T06:31:22Z

TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms. Currently we control this pin with a mux configuration as part of boot sequence. Current configuration results in the following voltage waveform: |---------------| (SET1 default 1.4V) | --------(programmed voltage) | <- (This switch happens on mux7,pullup) vdd_mpu(TPS) -----/ (OPP boot voltage) --------- (programmed voltage) vdd_core(TWL6030) -----------------------/ (OPP boot voltage) Problem 1) |<----- Tx ------>| timing violation for a duration Tx close to few milliseconds. Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP. By using GPIO as recommended as standard procedure by TI, the sequence changes to: -------- (programmed voltage) vdd_mpu(TPS) ------------/ (Opp boot voltage) --------- (programmed voltage) vdd_core(TWL6030) -------------/ (OPP boot voltage) NOTE: This does not attempt to address OMAP5 - Aneesh please confirm Reported-by: Isabelle Gros Reported-by: Jerome Angeloni Signed-off-by: Nishanth Menon