u-boot.git/board/ti, branch v2016.03

ARM : DRA7: Switch QSPI to use MODE-0 at 64MHz

2016-02-15T17:04:46Z

According to Data Manual(SPRS915P) of AM572x, TI QSPI controller on DRA74 EVM(rev 1.1+) can support up to 64MHz in MODE-0, whereas MODE-3 is limited to 48MHz. Hence, switch to MODE-0 for better throughput. Also, add IODelay parameters for the same. Signed-off-by: Vignesh R Reviewed-by: Tom Rini

board: ti: ks2_evm: remove board_eth_init when CONFIG_DM_ETH is defined

2016-02-08T15:10:45Z

remove board_eth_init when CONFIG_DM_ETH is defined Signed-off-by: Mugunthan V N Reviewed-by: Tom Rini Acked-by: Joe Hershberger

Use correct spelling of "U-Boot"

2016-02-06T11:00:59Z

Correct spelling of "U-Boot" shall be used in all written text (documentation, comments in source files etc.). Signed-off-by: Bin Meng Reviewed-by: Heiko Schocher Reviewed-by: Simon Glass Reviewed-by: Minkyu Kang

ARM: dra7x/am57x: Remove pin input/output config from WAKEUP pins

2015-11-22T02:50:19Z

The WAKEUP_X pins are always an input no matter the pinmux mode. However, the 18th bit that typical configures a pin as an input is considered reserved for the WAKEUP_X pins. Therefore, for any WAKEUP pin remove any configuration that sets that pin as an input. Since those pins are only inputs remove any output configuration from those pins. Signed-off-by: Franklin S Cooper Jr

ns16550: unify serial_omap

2015-11-22T02:50:17Z

Unify serial_omap, and use the generic binding. Signed-off-by: Thomas Chou Reviewed-by: Tom Rini Acked-by: Simon Glass

board/ti/am335x: add support for BeagleBone Green

2015-11-18T19:50:07Z

SeeedStudio BeagleBone Green (BBG) is clone of the BeagleBone Black (BBB) minus the HDMI port and addition of two Grove connectors (i2c2 and usart2). This board can be identified by the 1A value after A335BNLT (BBB) in the at24 eeprom: 1A: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 1a 00 00 00 |.U3.A335BNLT....|] http://beagleboard.org/green http://www.seeedstudio.com/wiki/Beaglebone_green In Mainline Kernel as of: https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=79a4e64c679d8a0b1037da174e4aea578c80c4e6 Patch tested on BeagleBone Black (rev C) and BeagleBone Green (production model) Signed-off-by: Robert Nelson CC: Tom Rini CC: Jason Kridner Reviewed-by: Tom Rini

board: ti: beagle_x15: Rename to indicate support for TI am57xx evms

2015-11-18T13:47:03Z

BeagleBoard X15 (http://beagleboard.org/x15) support in u-boot does actually support two different platform configuration offered by TI. In addition to BeagleBoard X15, it also supports the TMDXEVM5728 (or more commonly known as AM5728-evm). Information about the TI AM57xx EVM can be found here http://www.ti.com/tool/tmdxevm5728 The EVM configuration is 1-1 compatible with BeagleBoard X15 with the additional support for mPCIe, mSATA, LCD, touchscreen, Camera, push button and TI's wlink8 offering. Hence, we rename the beagle_x15 directory to am57xx to support TI EVMs that use the AM57xx processor. By doing this we have common code reuse. This sets the stage to have a common u-boot image solution for multiple TI EVMs such as that already done for am335x and am437x. This sets the stage for upcoming multiple TI EVMs that share the same code base. NOTE: Commit eae7ae185335 ("am437x: Add am57xx_evm_defconfig using CONFIG_DM") introduced DT support for beagle_x15 under am57xx_evm platform name. However, this ignored the potential confusion arising for users as a result. To prevent this, existing beagle_x15_defconfig is renamed as am57xx_evm_nodt_defconfig to denote that this is the "non device tree" configuration for the same platform. We still retain am57xx-beagle-x15.dts at this point, since we just require the common minimum dts. As a result of this change, users should expect changes in build procedures('make am57xx_evm_nodt_defconfig' instead of 'make beagle_x15_defconfig'). Hopefully, this would be a one-time change. Signed-off-by: Steve Kipisz Signed-off-by: Schuyler Patton Acked-by: Nishanth Menon Acked-by: Lokesh Vutla

board/ti/am335x: beaglebone stop muxing i2c1_pin_mux

2015-11-12T18:19:02Z

On the BeagleBone these i2c1 pins are routed to the expanasion header, where they can be defined as either pr1_usart0_Xxd/pwm0/spi0/i2c1, dont assume i2c1 Fixes: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/313894/1387696 Signed-off-by: Robert Nelson Reported-by: Matthijs van Duin CC: Tom Rini

board/ti: Update MAINTAINERS entries with more boards

2015-11-10T14:20:27Z

A few config files have been added without updating MAINTAINERS. Reported-by: Albert ARIBAUD Signed-off-by: Tom Rini

ARM: AM335x: mux: change mmc0 cd pinmux from mmc0_sdcd to gpio

2015-10-22T18:44:03Z

Currently omap_hsmmc driver doesn't use sdcd pin to detect whether the card is present or not. Instead the same pin is used as GPIO to detect card presence. So change the pin mux mode from mmc0_sdcd to gpio0_6. Signed-off-by: Mugunthan V N Reviewed-by: Tom Rini