u-boot.git/board/udoo, branch v2014.01

udoo: Add SATA support on uDoo Board.

2013-12-17T17:14:21Z

Add SATA support on uDoo Board. Signed-off-by: Giuseppe Pagano CC: Stefano Babic CC: Fabio Estevam

udoo: Fix watchdog during kernel boot.

2013-11-28T08:08:42Z

uDoo uses APX823-31W5 watchdog chip. Timeout is about 1.2 seconds. To disabled watchdog during kernel boot, WDI pin of that chip needs to be in "high impedance" state. I.mx6 gpio configuration does not contemplate tristate, so pin is set as input in high impedance. Signed-off-by: Giuseppe Pagano Reviewed-by: Fabio Estevam CC: Stefano Babic CC: Fabio Estevam

udoo: Add ethernet support (FEC + Micrel KSZ9031).

2013-11-28T07:28:54Z

Add Ethernet and networking support on uDoo board (FEC +phy Micrel KSZ9031). Ethernet speed is currently limited to 10/100Mbps. Signed-off-by: Giuseppe Pagano Tested-by: Fabio Estevam CC: Stefano Babic CC: Fabio Estevam

udoo: Move and optimize platform register setting.

2013-11-28T07:28:54Z

Previous uDoo configuration adopts register settings for DDR3, clock, muxing, etc. taken from Nitrogen6x. uDoo schematics is rather different from that board, and it needs customized setting for most of the registers. All this changes can be considered atomical since it is part of initial support of the board. Patch changes uDoo configuration files path to a specific one, and adopt optimized value for every configured register. Signed-off-by: Giuseppe Pagano Tested-by: Fabio Estevam CC: Stefano Babic CC: Fabio Estevam

i.MX6DQ/DLS: replace pad names with their Linux kernel equivalents

2013-11-13T09:19:50Z

Signed-off-by: Eric Nelson

Merge branch 'iu-boot/master' into 'u-boot-arm/master'

2013-11-09T21:59:47Z

Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h

udoo: Add initial support for mx6q udoo board

2013-10-17T07:44:20Z

Add basic support for mx6q udoo board. For further information about Udoo board: http://www.udoo.org/ Tested booting a mainline device tree kernel and a Yocto rootfs from mmc. Signed-off-by: Fabio Estevam