Nand and QSPI are not defined now but this will be extended. Based on selected bootmode boot_targets are rewritten. Patch also contains detection if variables are saved. If yes don't rewrite boot_targets variable. Also move variable setup to the end of file because SCSI needs to be defined before others macros are using it. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Alexander Graf <agraf@suse.de>
Select MSR instructions via Kconfig instead of xparameters.h. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Toolchain can use some flags by default based on cpu version. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove autogenerated config.mk and select CPU options via Kconfig. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Extending Kconfig for adding new platform is a lot of work for nothing. Setting SYS_CONFIG_NAME directly in Kconfig and remove all dependencies on TARGET_ZYNQ_* options including SPL. As a side-effect it also remove custom init folder for ps7_init_gpl.* files. Folder is chosen based on device-tree file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Support RAM and MMC boot mode in SPL also with SPL_FIT images. In MMC boot mode two boot options are available: 1) Boot flow with ATF(EL3) and full U-Boot(EL2): aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin mkimage -A arm64 -O linux -T kernel -C none -a 0xfffe5000 -e 0xfffe5000 -d bl31.bin atf.ub cp spl/boot.bin <sdcard fat partition> cp atf.ub <sdcard fat partition> cp u-boot.bin <sdcard fat partition> 2) Boot flow with full U-Boot(EL3): cp spl/boot.bin <sdcard> cp u-boot*.img <sdcard> 3) emmc boot mode dd if=/dev/zero of=sd.img bs=1024 count=1024 parted sd.img mktable msdos parted sd.img mkpart p fat32 0% 100% kpartx -a sd.img mkfs.vfat /dev/mapper/loop0p1 mount /dev/mapper/loop0p1 /mnt/ cp spl/boot.bin /mnt cp u-boot.img /mnt cp u-boot.bin /mnt cp atf.ub /mnt umount /dev/mapper/loop0p1 kpartx -d sd.img cp sd.img /tftpboot/ and program it via u-boot tftpb 10000 sd.img mmcinfo mmc write 10000 0 $filesize mmc rescan mmc part ls mmc 0 psu_init() function contains low level SoC setup generated for every HW design by Xilinx design tools. xil_io.h is only supporting file to fix all dependencies from tools. The same solution was used on Xilinx Zynq. The patch also change CONFIG_SYS_INIT_SP_ADDR to the end of OCM which stays at the same location all the time. Bootrom expects starting address to be at 0xfffc0000 that's why this address is SPL_TEXT_BASE. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for on board eeprom with programmed MAC for using in u-boot to have uniq address for every board. Most of the time uniq MAC address is on a label on the board. If address is not programmed use these command to program it. On zcu102: ZynqMP> mm.b 0 00000000: 00 ? 00 00000001: a0 ? 0a 00000002: 35 ? 35 00000003: 02 ? 02 00000004: 00 ? ef 00000005: 00 ? 67 00000006: 00 ? q i2c dev 5 i2c write 0 54 20 6 i2c md 54 20 Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Including netdev.h is causing compilation warning: + int fecmxc_register_mii_postcall(struct eth_device *dev, int (*cb)(int)); + ^ w+In file included from ../board/xilinx/zynqmp/zynqmp.c:9:0: w+../include/netdev.h:204:41: warning: ‘struct eth_device’ declared inside parameter list [enabled by default] w+../include/netdev.h:204:41: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default] This patch removes it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define u64 types to be usable on 32bit system because of 64bit address and size cells and 32bit shifts in the code. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is example how to change u-boot to support more memory banks read from DT. Signed-off-by: Michal Simek <michal.simek@xilinx.com>