u-boot.git/board, branch v2011.06-rc2

Minor coding style cleanup

2011-06-02T21:18:32Z

Signed-off-by: Wolfgang Denk

Merge branch 'master' of git://git.denx.de/u-boot-sh

2011-06-01T20:16:19Z

* 'master' of git://git.denx.de/u-boot-sh: sh: sh7785lcr: Update BSC of USB area

SMDKV310: Fix incorrect conditional compilation for MIU linear mapping

2011-06-01T17:45:59Z

Fix the incorrect macro check for MIU linear mapping conditional compilation. Signed-off-by: Thomas Abraham Acked-by: Minkyu Kang

SMDKV310: CPU fequency and mmc_pre_ratio modified

2011-06-01T17:41:32Z

Modifies CPU Frequency to 1GHz and removes hard coding of mmc_pre_ratio for MMC Channel2 in FSYS2 register. Signed-off-by: Chander Kashyap Acked-by: Minkyu Kang

armv7: Add support for ST-Ericsson U8500 href platform

2011-06-01T17:31:03Z

Minimal platform support to boot linux from SD. Supported devices/hw limited to external MMC/SD slot, GPIO, I2C and minimal PRCMU. Signed-off-by: John Rigby CC: Albert Aribaud

sh: sh7785lcr: Update BSC of USB area

2011-06-01T01:20:19Z

A value of BSC of the USB was wrong. This updates this. Signed-off-by: Nobuhiro Iwamatsu

ARMV7: Vexpress: Add missing MMC header

2011-05-31T20:25:23Z

Add a header file with the missing function prototype to fix ca9x4_ct_vxp.c: In function 'cpu_mmc_init': ca9x4_ct_vxp.c:93: warning: implicit declaration of function 'arm_pl180_mmci_init' introduced by commit "ARMV7: Vexpress: Add MMC support" (f0c64526b7e51ba997a0f1baf9e74e6d497b957e) Signed-off-by: Dirk Behme CC: Andy Fleming CC: Matt Waddel

arm/km: update mgcoge3un board support

2011-05-31T17:46:19Z

We change default settings for egiga on mgcoge3un. The reason we need this is that we have the gig port on mgcoge3un connected using a back-to-back pair of PHYs. There are no magnetics and because of that the port has to be run with a fixd configuration and auto-negotiation must be disabled. In the default mode the egiga driver uses autoneg to determine port speed - which defaults to 1G (we need 100M full duplex). Add wait for the GPIO line connected to mgcoge3ne before starting mgcoge3un. A board specific ethernet present function was added, because on this board ethernet is always present. The BOCO FPGA access was enhanced and changed to use register definitions. Signed-off-by: Holger Brunck Signed-off-by: Valentin Longchamp Acked-by: Heiko Schocher cc: Wolfgang Denk cc: Detlev Zundel cc: Prafulla Wadaskar

arm/km: rename mgcoge2un to mgcoge3un

2011-05-31T17:45:59Z

The mgcoge2un target was only an intermediate step to mgcoge3un. For this reason the mgcoge2un support was moved to mgcoge3un, because it isn't needed to support both targets. We add the BootROM init file for the mgcoge3un memphis RAM. We also move the suen3 and suen8 boards into the correct category in the MAINTAINERS file. Signed-off-by: Valentin Longchamp Signed-off-by: Holger Brunck Acked-by: Heiko Schocher cc: Wolfgang Denk cc: Detlev Zundel cc: Prafulla Wadaskar

arm/km: introduce bootcount env variable and clean km_arm

2011-05-31T17:45:27Z

This environment variable is used to set the bootcount address for the kernel. last_stage_init is not available for arm platforms. So the calls to set_km_var and set_bootcount_addr are done in misc_init_r. Additionally some unneeded printouts were removed. Signed-off-by: Valentin Longchamp Signed-off-by: Holger Brunck Acked-by: Heiko Schocher cc: Wolfgang Denk cc: Detlev Zundel cc: Prafulla Wadaskar