* 'master' of git://git.denx.de/u-boot-sh:
  sh: ecovec: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
  sh: Fix rsk7264 pin setup for on-board ethernet

This sets up the external ethernet IRQ pin.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Do the same AXI cache and Qos settings done already in the
SabreLite imximage.cfg for the ARM2 board, too.

It fixes a display flash issue caused by low priority of
the display IDMA channel.

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Jason Chen <b02280@freescale.com>
CC: Jason Liu <r64343@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <festevam@gmail.com>
Acked-by: Jason Liu <r64343@freescale.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

The board revision is detected accessing to the pmic,
that is not available before relocation (I2C).
This generates the following error:

CPU:   Freescale i.MX35 rev 2.0 at 532 MHz.
Reset cause: WDOG
<reg num> = 7 is invalid. Should be less than 0
Board: MX35 PDK 1.0

The revision number is wrong, as a default value is printed
(tested on a mx35pdk Rev. 2.0).

Move the output in the board_late_init(), when
pmic can be accessed.

Signed-off-by: Stefano Babic <sbabic@denx.de>

enable_caches() is implemented now in cpu.c for
ARM1136.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>

Currently, board files are setting this field to 0x01
which the manual says is a reserved value. Change to
use the default of 0x02 - 128 cycles.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>

The reset_net_chip() function has wrong timings for the reset pulse.

This appeared to work until:
0607e2b (ARMV7: OMAP: Write more than 1 byte at a time in i2c_write)

Fix the Ethernet support by introducing right timings.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>

Remove userbutton command and do the detection in board config file using the gpio command

Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>

* 'master' of git://git.denx.de/u-boot-net:
  net/designware: Change timeout loop implementation
  net/designware: Set ANAR to 0x1e1
  net/designware: Program phy registers when auto-negotiation is ON
  net/designware: Try configuring phy on each dw_eth_init
  net/designware: Consecutive writes must have delay
  net/designware: Phy address fix
  net/designware: Fix the max frame length size
  net/designware: Fix to restore hw mac address
  microblaze: Wire up LL_TEMAC driver initialization
  microblaze: Add faked LL_TEMAC driver configuration
  microblaze: Enable several ethernet driver compilation
  net: ll_temac: Add LL TEMAC driver to u-boot
  Update net subsystem maintainer in doc/git-mailrc
  net/eth.c: fix eth_write_hwaddr() to use dev->enetaddr as fall back
  mvgbe: remove warning for unused methods