u-boot.git/board, branch v2016.03-rc2

ARM : DRA7: Switch QSPI to use MODE-0 at 64MHz

2016-02-15T17:04:46+00:00

According to Data Manual(SPRS915P) of AM572x, TI QSPI controller on
DRA74 EVM(rev 1.1+) can support up to 64MHz in MODE-0, whereas MODE-3 is
limited to 48MHz. Hence, switch to MODE-0 for better throughput.
Also, add IODelay parameters for the same.

Signed-off-by: Vignesh R 
Reviewed-by: Tom Rini

OMAP3LOGIC: Update maintainer

2016-02-15T17:04:45+00:00

I will take this over from Peter Barada, since I work with it daily
at Logic PD.

Signed-off-by: Adam Ford 
Acked-by: Peter Barada

sniper: Drop references to P970

2016-02-08T15:24:19+00:00

There are various different boards with the same hardware sold as LG Optimus
Black, such as P970, P970g and KU5900. Since this port is functional for all
variants, it doesn't make sense to keep references to P970.

Signed-off-by: Paul Kocialkowski 
Reviewed-by: Tom Rini

rpi: set ethaddr as well

2016-02-08T15:10:49+00:00

Let's set "ethaddr" when we get the ethernet address too, so that
fdt_fixup_ethernet() sets the address in the device tree and the Linux
driver can pick it up.

Signed-off-by: Lubomir Rintel 
Tested-by: Stephen Warren

board: ti: ks2_evm: remove board_eth_init when CONFIG_DM_ETH is defined

2016-02-08T15:10:45+00:00

remove board_eth_init when CONFIG_DM_ETH is defined

Signed-off-by: Mugunthan V N 
Reviewed-by: Tom Rini 
Acked-by: Joe Hershberger

OMAP3: omap3_logic: Enable Android Fastboot

2016-02-08T15:10:43+00:00

Android Fastboot requires USB.  The TWL4030 PMIC on omap3_logic handles USB traffic.
This patch sets up the USB gadget and Android Fastboot to match what is done in the
omap3_beagle project.

Signed-off-by: Adam Ford 
Reviewed-by: Tom Rini

OMAP3: Enable SPL on omap3_logic

2016-02-08T15:10:39+00:00

Previously, Omap3_logic assumed X-loader was present.  With this
patch, we can finally replace X-loader with an MLO generated by
U-Boot.  This requires ECC to be setup to match the Linux Kernel
and the PBIAS confgured for the SD card.

Signed-off-by: Derald D. Woods 
Signed-off-by: Adam Ford 
Reviewed-by: Tom Rini

rpi: fix up Model B entries

2016-02-08T15:10:38+00:00

The P5 header was not present on "Model B" any board prior to Revision 2.0,
there's no need for a separate device tree.

Also, it looks like "rev2" is incorrectly used to only cover the 512MiB
memory models; there also were 256MiB 2.0 boards.

I don't have all of the boards to check this, I'm following this table:
http://elinux.org/RPi_HardwareHistory#Board_Revision_History

Signed-off-by: Lubomir Rintel

rpi: link to another model number info source

2016-02-08T15:10:37+00:00

This source has been blessed by Dom Cobley at the RPi Foundation, so seems
like the best source to refer to. It's a superset of and consistent with
the other sources.

Cc: Lubomir Rintel 
Cc: Eric Anholt 
Signed-off-by: Stephen Warren

serial: serial_stm32: move clock config from driver to board

2016-02-08T15:10:36+00:00

This patch removes the uart clock enable from serial driver & move it in the
board code.

Signed-off-by: Vikas Manocha 
Reviewed-by: Simon Glass