Fixes for 2020.01
-----------------
- Fixes for Nitrogen6x
- Fix corruption for mx51evk
- colibri i.MX6: fix broken ESDHC conversion
- mx6sxsabresd: fix broken mmcdev
- imx6q_logic: cleanup boot sequence
- update ATF for imx8mq_evk
- pfuze: fix pmic_get()

Travis CI: https://travis-ci.org/sbabic/u-boot-imx/builds/630007464

- Orange Pi Zero Plus 2 support
- sunxi psci, prcm fixes

The board_boot_order() function currenly assumes that the boot source
is MMC/eMMC, but this isn't true for the NAND devices.

This patch cleans up board_boot_order() to check for NAND, SD, ESD,
MMC or EMMC.  Anything beyond these are not supported, so it will
default back to the serial downloader if any of those devices are not
available.

Fixes: 9fb50c68daa6 ("ARM: imx6q_logic: Fix MMC2 booting")

Signed-off-by: Adam Ford <aford173@gmail.com>

The next patch adds CONFIG_MX6QDL so that
errata will be enabled again.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>

Following the README instructions leads to a non-booting
U-Boot:

U-Boot SPL 2020.01-rc3-00070-g9a0cbae22a (Nov 25 2019 - 13:08:24 -0300)
PMIC:  PFUZE100 ID=0x10
DDRINFO: start DRAM init
DDRINFO:ddrphy calibration done
DDRINFO: ddrmix config done
Normal Boot
Trying to boot from MMC2

(It hangs here)

Use the "imx_4.19.35_1.0.0" ATF branch instead, which
fixes such problem and allow the boot to complete again.

Suggested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>

Currently the following hang is observed when booting a imx6sx-sdb
board:

U-Boot 2020.01-rc5-00004-g643366bcd5 (Dec 19 2019 - 14:56:23 -0300)

CPU:   Freescale i.MX6SX rev1.0 996 MHz (running at 792 MHz)
CPU:   Extended Commercial temperature grade (-20C to 105C) at 32C
Reset cause: POR
Model: Freescale i.MX6 SoloX SDB RevB Board
Board: MX6SX SABRE SDB revA
DRAM:  1 GiB
initcall sequence bffd8514 failed at call 87804cc0 (err=-19)
### ERROR ### Please RESET the board ###

When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address.

Fix the pmic_get() parameter to fix the boot regression.

Tested on a imx6sx-sdb and imx6q-sabresd boards.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>

Not all CONFIG_FSL_ESDHC defines were properly replaced with
CONFIG_FSL_ESDHC_IMX, which broke U-boot proper booting on
Colibri iMX6 SoMs.

U-boot is stuck after this message:
Commercial temperature grade DDR3 timings, 64bit bus width.
Trying to boot from MMC1

Fixes: e37ac717d7("Convert to use fsl_esdhc_imx for i.MX platforms")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>

As per the email discussion[0], add myself as a maintainer to
OMAPL138_LCDK and drop Peter's entry.

[0] http://u-boot.10912.n7.nabble.com/OMAP-L138-LCDK-giving-up-maintainership-td394211.html

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

Orangepi Zero Plus 2 is an open-source single-board computer, available
in two Allwinner SOC variants, H3 and H5. We add support for H3 variant
here, as the H5 is already supported.

H3 Orangepi Zero Plus 2 has:
- Quad-core Cortex-A7
- 512MB DDR3
- microSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG + power supply

Sync dts from linux v5.2 commit:
"ARM: dts: sunxi: h3/h5: Remove stale pinctrl-names entry"
(sha1: 75f9a058838be9880afd75c4cb14e1bf4fe34a0b)
Commit:
"ARM: dts: sun8i: h3: Refactor the pinctrl node names"
(sha1: a4dc791974e568a15f7f37131729b1a6912f4811)
has been avoided as it breaks U-Boot build.

Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

- fix DRAM bank detection for unified binary
- fix 32bit RPi4 config