u-boot.git/board, branch v2023.04

Merge branch 'rpi-2023.04' of https://source.denx.de/u-boot/custodians/u-boot-raspberrypi

2023-03-24T21:00:41Z

- Fixes for booting newer revs of the SoC in the Raspberry Pi 4 - Propagate some firmware DT properties to the loaded DT - Update the Zero2W upstream DT name

Merge tag 'u-boot-amlogic-20230322' of https://source.denx.de/u-boot/custodians/u-boot-amlogic

2023-03-22T13:21:41Z

- odroid-go-ultra: setup PMIC regulators at board init

board: m5253demo: remove floating point flash size calculation

2023-03-15T00:52:15Z

This board is using floating point arithmetic to display the SST39VF6401B flash size. This actually generates errors with toolchains without appropriate sw fp math functions available. SST39VF6401B is the only flash for wich the size is displayed, it's size is 8192KB and floating point calculation seems not needed. Removing it. Signed-off-by: Angelo Dureghello

m68k: rename CONFIG_MCFTMR to CFG_MCFTMR

2023-03-15T00:41:57Z

This is not a Kconfig option so changing to _CFG. Signed-off-by: Angelo Durgehello

board: stmark2: fix clock value

2023-03-15T00:38:19Z

Fix totally blank console at boot, clock value must be decimal, as for the 30Mhz external crystal. Fixes: 26e5944ec90c ("stmark2: Migrate CONFIG_SYS_EXTRA_OPTIONS to Kconfig") Signed-off-by: Angelo Dureghello Reviewed-by: Tom Rini

rpi: Update the RPi Zero 2W DT filename

2023-03-14T12:12:13Z

Update the Raspberry Pi Zero 2W device tree file name to match what landed upstream. Signed-off-by: Peter Robinson

rpi: Copy eth PHY address from fw DT to loaded DT

2023-03-14T12:12:13Z

Some Raspberry Pi 400 boards, specifically rev 1.1, have a different address for the ethernet PHY device than what is provided by the kernel DTB. The correct address is provided by the firmware, so we should carry it over into the loaded device tree so that ethernet works on such boards. Signed-off-by: Antoine Mazeas Signed-off-by: Peter Robinson

rpi: Copy properties from firmware dtb to the loaded dtb

2023-03-14T12:12:13Z

The RPI firmware adjusts several property values in the dtb it passes to u-boot depending on the board/SoC revision. Inherit some of these when u-boot loads a dtb itself. Specificaly copy: * /model: The firmware provides a more specific string * /memreserve: The firmware defines a reserved range, better keep it * emmc2bus and pcie0 dma-ranges: The C0T revision of the bcm2711 Soc (as present on rpi 400 and some rpi 4B boards) has different values for these then the B0T revision. So these need to be adjusted to boot on these boards * blconfig: The firmware defines the memory area where the blconfig stored. Copy those over so it can be enabled. * /chosen/kaslr-seed: The firmware generates a kaslr seed, take advantage of that. Signed-off-by: Sjoerd Simons Signed-off-by: Antoine Mazeas Reviewed-by: Simon Glass Signed-off-by: Peter Robinson

ARM: meson: odroid-go-ultra: setup PMIC regulators are board init

2023-03-14T08:03:16Z

The Odroid Go Ultra has 2 chained PMICs RK818 and RK818, and needs an adjustment on the BUCK and LDO values. Add the initial regulators values in -u-boot.dtsi & run the initial regulator setup in a new odroid-go-ultra board. Proper OTG and BOOST regulators are still missing to have USB-A host properly working. Link: https://lore.kernel.org/r/20230210-u-boot-odroid-go-ultra-pmics-setup-v1-1-1f16d62b76af@linaro.org Signed-off-by: Neil Armstrong

board: rock5b-rk3588: add memory gaps into kernel's DTB

2023-02-28T10:07:29Z

RK3588 has two memory gaps when using 16 GiB DRAM size: [0x3fc000000 , 0x3fc500000] and [0x3fff00000 , 0x3ffffffff] If the kernel is agnostic to these gaps, accessing the area causes a SError panic. Hence, add reserved memory areas in kernel's DTB before booting. Signed-off-by: Eugen Hristev Reviewed-by: Kever Yang