u-boot.git/cmd/Kconfig, branch v2021.10

mmc: Add support for enumerating MMC card in a given mode using mmc command

2021-09-10T10:17:04Z

Add support for enumerating MMC card in a given mode using mmc rescan and mmc dev commands. The speed mode is provided as the last argument in these commands and is indicated using the index from enum bus_mode in include/mmc.h. A speed mode can be set only if it has already been enabled in the device tree. Signed-off-by: Aswath Govindraju Reviewed-by: Jaehoon Chung Tested-by: Jaehoon Chung

Rename DRIVERS_MISC_SUPPORT to DRIVERS_MISC

2021-07-28T18:29:37Z

Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass

cmd: setexpr: add format string handling

2021-07-27T18:50:47Z

Add format string handling operator to the setexpr command. It allows to use C or Bash like format string expressions to be evaluated with the result being stored inside the environment variable name. setexpr fmt [value]... The following example setexpr foo fmt "%d, 0x%x" 0x100 ff will result in $foo being set to "256, 0xff". Signed-off-by: Roland Gaudig Reviewed-by: Simon Glass

treewide: Test on CONFIG_USB_HOST (or CONFIG_CMD_USB) not CONFIG_USB

2021-07-19T01:05:31Z

As the logic here is only used when we have a USB host controller, test on CONFIG_USB_HOST rather than CONFIG_USB in general. This lets us move towards using CONFIG_USB only as a menu symbol to say that we have some form of USB, and then USB_HOST or USB_GADGET depending on the role that USB plays within the build. Signed-off-by: Tom Rini

usb: Add correct depends for CMD_USB_MASS_STORAGE

2021-07-08T02:22:42Z

We cannot build this without USB_GADGET_DOWNLOAD support enabled, add the appropriate depends line. Signed-off-by: Tom Rini

Revert "TEST: USB_HOST not USB"

2021-06-30T17:10:02Z

This reverts commit 4e1903a645453deab5ec5dd1cf4f0061469b99c3. This local commit was not intended to be pushed out. Signed-off-by: Tom Rini

TEST: USB_HOST not USB

2021-06-30T15:38:52Z

Signed-off-by: Tom Rini

cmd: Add dependency for ums command

2021-06-08T22:13:26Z

Add the missing dependency for the command ums: - CONFIG_BLK: call of blk_* functions in usb_mass_storage.c - CONFIG_USB_GADGET: required to select CONFIG_USB_FUNCTION_MASS_STORAGE Signed-off-by: Patrick Delaunay Reviewed-by: Heinrich Schuchardt

cmd: add support for a new "extension" command

2021-05-13T17:09:05Z

This patch adds a new "extension" command, which aims at detecting extension boards connected to the hardware platform, and apply the Device Tree overlays that describe the hardware present on those extension boards. In order to enable this mechanism, board-specific code must implement the extension_board_scan() function that fills in a linked list of "struct extension", each describing one extension board. In addition, the board-specific code must select the SUPPORT_EXTENSION_SCAN Kconfig boolean. Based on this: - "extension scan" makes the generic code call the board-specific extension_board_scan() function to retrieve the list of detected extension boards. - "extension list" allows to list the detected extension boards. - "extension apply |all" allows to apply the Device Tree overlay(s) corresponding to one, or all, extension boards The latter requires two environment variables to exist and set one variable to run: - extension_overlay_addr: the RAM address where to load the Device Tree overlays - extension_overlay_cmd: the U-Boot command to load one overlay. Indeed, the location and mechanism to load DT overlays is very setup specific. - extension_overlay_name: set by the command: the name of the DT which will be load during the execution. When calling the command described in the extension_overlay_cmd variable, the variable extension_overlay_name will be defined. So a typical extension_overlay_cmd will look like this: extension_overlay_cmd=load mmc 0:1 $extension_overlay_addr /boot/$extension_overlay_name Here is an example on how to use it: => run loadfdt => fdt addr $fdtaddr => setenv extension_overlay_addr 0x1000 => setenv extension_overlay_cmd 'load mmc 0:1 ${extension_overlay_addr} /boot/${extension_overlay_name}' => extension scan Found 1 extension board(s). => extension apply 0 519 bytes read in 3 ms (168.9 KiB/s) Signed-off-by: Kory Maincent Reviewed-by: Maxime Ripard

Add support for stack-protector

2021-04-20T11:31:12Z

Add support for stack protector for UBOOT, SPL, and TPL as well as new pytest for stackprotector Signed-off-by: Joel Peshkin Adjust UEFI build flags. Signed-off-by: Heinrich Schuchardt