Add Kconfig option(CONFIG_CMD_MP) to enable or disable multiprocessor
commands. Compile cmd/mp.c based on CONFIG_CMD_MP.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Commit 98f705c9cefd ("powerpc: remove 4xx support") removed (in 2017) the
last code that made use of bedbug debugger support. Since there aren't
any boards left that define either CONFIG_CMD_BEDBUG or a real
bedbug_init(), drop this feature from u-boot.

Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config

This converts the following to Kconfig:
   CONFIG_JFFS2_DEV
   CONFIG_JFFS2_LZO
   CONFIG_JFFS2_NAND
   CONFIG_JFFS2_PART_OFFSET
   CONFIG_JFFS2_PART_SIZE

Signed-off-by: Tom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SYS_MEMTEST_START
   CONFIG_SYS_MEMTEST_END

This is removing unused defines and correcting the default value to be
0x0 as we are a hex symbol.

Signed-off-by: Tom Rini <trini@konsulko.com>

Allow the kaslr-seed value in the chosen node to be set from a hardware
rng source.

Tested on a Rockchip PX30 (Odroid Go Advance), you must have loaded
the devicetree first and prepared it for editing. On my device the
workflow goes as follows:

setenv dtb_loadaddr "0x01f00000"
load mmc 0:1 ${dtb_loadaddr} rk3326-odroid-go2.dtb
fdt addr ${dtb_loadaddr}
fdt resize
kaslrseed

and the output can be seen here:
fdt print /chosen
chosen {
        kaslr-seed = <0x6f61df74 0x6f7b996c>;
        stdout-path = "serial2:115200n8";
};

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

At present there are Kconfig options for tracing, but sandbox uses
plain #defines to set them. Correct this and make the tracing command
default to enabled so that this is not needed.

Signed-off-by: Simon Glass <sjg@chromium.org>

Prepare v2021.10-rc4

Signed-off-by: Tom Rini <trini@konsulko.com>

# gpg: Signature made Tue 14 Sep 2021 06:58:32 PM EDT
# gpg:                using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C
# gpg: Good signature from "Thomas Rini <trini@konsulko.com>" [ultimate]

# Conflicts:
#	board/Arcturus/ucp1020/spl.c
#	cmd/mvebu/Kconfig
#	common/Kconfig.boot
#	common/image-fit.c
#	configs/UCP1020_defconfig
#	configs/sifive_unmatched_defconfig
#	drivers/pci/Kconfig
#	include/configs/UCP1020.h
#	include/configs/sifive-unmatched.h
#	lib/Makefile
#	scripts/config_whitelist.txt

Add support for enumerating MMC card in a given mode using mmc rescan and
mmc dev commands. The speed mode is provided as the last argument in these
commands and is indicated using the index from enum bus_mode in
include/mmc.h. A speed mode can be set only if it has already been enabled
in the device tree.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>