u-boot.git/cmd/Kconfig, branch v2024.01

net: Get pxe config file from dhcp option 209

2023-11-05T18:28:40Z

Allow dhcp server pass pxe config file full path by using option 209 Signed-off-by: Sean Edmond

cmd: mmc: Add mmc reg read command for reading card registers

2023-11-01T01:09:21Z

Add extension to the 'mmc' command to read out the card registers. Currently, only the eMMC OCR/CID/CSD/EXTCSD/RCA/DSR register are supported. A register value can either be displayed or read into an environment variable. Tested-by: Jaehoon Chung Reviewed-by: Jaehoon Chung Signed-off-by: Marek Vasut Reviewed-by: Fabio Estevam

Kconfig: Remove all default n/no options

2023-10-30T19:32:49Z

Similar change was done by commit b4c2c151b14b ("Kconfig: Remove all default n/no options") and again sync is required. default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek Reviewed-by: Svyatoslav Ryhel # tegra Reviewed-by: Tom Rini Reviewed-by: Angelo Dureghello

rockchip: cmd: add rkmtd command

2023-10-24T07:55:17Z

The command rkmtd creates a virtual block device to transfer Rockchip boot block data to and from NAND with block orientated tools like "ums" and "rockusb". It uses the Rockchip MTD driver to scan for boot blocks and copies data from the first block in a GPT formated virtual disk. Data must be written in U-boot "idbloader.img" format and start at partition "loader1" offset 64. The data header is parsed for length and offset. When the last sector is received it erases up to 5 erase blocks on NAND and writes bootblocks in a pattern depending on the NAND ID. Data is then verified. When a block turns out bad the block header is discarded. Signed-off-by: Johan Jonker Reviewed-by: Simon Glass

cli: Add a command to show cmdline history

2023-10-11T19:43:54Z

There is a function for this but it is never used. Showing the history is a useful feature, so add a new 'history' command. Signed-off-by: Simon Glass

cmd: xxd: move xxd into shell commands

2023-09-30T19:24:44Z

Move xxd into shell command section. Signed-off-by: Roger Knecht Reviewed-by: Simon Glass

cmd: thordown: Add proper dependency for CMD_THOR_DOWNLOAD

2023-09-21T11:20:11Z

When CONFIG_CMD_USB and CONFIG_USB are disabled some compilation errors are seen as below. cmd/thordown.o: in function `usb_gadget_initialize': include/linux/usb/gadget.h:981: undefined reference to `board_usb_init' cmd/thordown.o: in function `do_thor_down': cmd/thordown.c:68: undefined reference to `g_dnl_unregister' cmd/thordown.o: in function `usb_gadget_release': include/linux/usb/gadget.h:986: undefined reference to `board_usb_cleanup' cmd/thordown.o: in function `do_thor_down': cmd/thordown.c:41: undefined reference to `g_dnl_register' cmd/thordown.c:48: undefined reference to `thor_init' cmd/thordown.c:56: undefined reference to `thor_handle' gnu/aarch64/lin/aarch64-linux/bin/aarch64-linux-gnu-ld.bfd: line 4: 8485 Segmentation fault (core dumped) $CC --sysroot=$LIBC --no-warn-rwx-segment "$@" Makefile:1779: recipe for target 'u-boot' failed make: *** [u-boot] Error 139 make: *** Deleting file 'u-boot' Add dependency of USB_GADGET_DOWNLOAD for CONFIG_CMD_THOR_DOWNLOAD to fix the errors. Signed-off-by: Ashok Reddy Soma Signed-off-by: Venkatesh Yadav Abbarapu Reviewed-by: Tom Rini Link: https://lore.kernel.org/r/20230904031528.11817-2-venkatesh.abbarapu@amd.com Signed-off-by: Michal Simek

Merge tag 'v2023.10-rc3' into next

2023-08-21T21:32:17Z

Prepare v2023.10-rc3 Signed-off-by: Tom Rini

Kconfigs: Correct default of "0" on hex type entries

2023-08-09T13:21:42Z

It is not a parse error to have a default value of "0" for a "hex" type entry, instead of "0x0". However, "0" and "0x0" are not treated the same even by the tools themselves. Correct this by changing the default value from "0" to "0x0" for all hex type questions that had the incorrect default. Fix one instance (in two configs) of a default of "0" being used on a hex question to be "0x0". Remove the cases where a defconfig had set a value of "0x0" to be used as the default had been "0". Signed-off-by: Tom Rini Reviewed-by: Simon Glass

arm_ffa: introduce armffa command

2023-08-08T14:22:03Z

Provide armffa command showcasing the use of the U-Boot FF-A support armffa is a command showcasing how to invoke FF-A operations. This provides a guidance to the client developers on how to call the FF-A bus interfaces. The command also allows to gather secure partitions information and ping these partitions. The command is also helpful in testing the communication with secure partitions. For more details please refer to the command documentation [1]. A Sandbox test is provided for the armffa command. [1]: doc/usage/cmd/armffa.rst Signed-off-by: Abdellatif El Khlifi Reviewed-by: Simon Glass Cc: Tom Rini Cc: Ilias Apalodimas Cc: Jens Wiklander Cc: Heinrich Schuchardt