u-boot.git/cmd/Makefile, branch v2020.10-rc2

fs/squashfs: add filesystem commands

2020-08-08T02:31:32+00:00

Add 'ls' and 'load' commands.

Signed-off-by: Joao Marcos Costa

cmd: add clone command

2020-08-05T03:29:59+00:00

This patch adds a feature for block device cloning similar to dd
command, this should be useful for boot-strapping a device where
usb gadget or networking is not available. For instance one can
clone a factory image into a blank emmc from an external sd card.

Signed-off-by: John Chau

cmd: button: add a new 'button' command

2020-07-29T01:30:39+00:00

Adds a command 'button' that provides the list of buttons
supported by the board, and the state of a button.

Reviewed-by: Simon Glass 
Signed-off-by: Philippe Reynes

cmd: drop fitupd command

2020-07-16T10:37:01+00:00

The `fitupd' command is not used by any board. The `dfu tftp' command
provides the same capabilities.

So let's drop the `fitupd' command.

Signed-off-by: Heinrich Schuchardt

rtc: add rtc command

2020-07-09T04:02:45+00:00

Mostly as an aid for debugging RTC drivers, provide a command that can
be used to read/write arbitrary registers (assuming the driver
provides the read/write methods or their single-register-at-a-time
variants).

Reviewed-by: Simon Glass 
Reviewed-by: Heiko Schocher 
Signed-off-by: Rasmus Villemoes

cmd: add a panic command

2020-07-08T21:21:46+00:00

Even in boot scripts it may be needed to "panic" when all options
are exhausted and the device specification specifies hanging
instead of resetting the board.

So add a new panic command that just wraps around the core panic
call in U-Boot and can take an optional message.

Signed-off-by: Heiko Stuebner 
Reviewed-by: Simon Glass 
Reviewed-by: Tom Rini

cmd: blkls: Add blkls command

2020-07-07T19:37:13+00:00

Add a command to print a list of available block device drivers,
and for each, the list of known block devices.

Signed-off-by: Niel Fourie 
Cc: Simon Glass 
Cc: Stefan Roese 
Reviewed-by: Simon Glass 
Reviewed-by: Stefan Roese

acpi: Add an acpi command

2020-04-30T09:16:12+00:00

It is useful to dump ACPI tables in U-Boot to see what has been generated.
Add a command to handle this.

To allow the command to find the tables, add a position into the global
data.

Support subcommands to list and dump the tables.

Signed-off-by: Simon Glass 
Reviewed-by: Wolfgang Wallner

cmd: Add unlz4 command

2020-04-17T16:32:12+00:00

This command is a new command called "unlz4" that decompresses from memory
into memory.
Used with the CONFIG_CMD_UNLZ4 optionenabled.

Signed-off-by: Yusuke Ashiduka 
[trini: Use %zd / %zX not %ld / %lX in printf]
Signed-off-by: Tom Rini

cmd: abootimg: Add abootimg command

2020-02-04T03:37:24+00:00

This command can be used to extract fields and image payloads from
Android Boot Image. It can be used for example to implement boot flow
where dtb is taken from boot.img (as v2 incorporated dtb inside of
boot.img). Using this command, one can obtain needed dtb blob from
boot.img in scripting manner, and then apply needed dtbo's (from "dtbo"
partition) on top of that, providing then the resulting image to bootm
command in order to boot the Android.

Also right now this command has the sub-command to get an address and
size of recovery dtbo from recovery image (for non-A/B devices only,
see [1,2] for details).

It can be tested like this:

    => mmc dev 1
    => part start mmc 1 boot_a boot_start
    => part size mmc 1 boot_a boot_size
    => mmc read $loadaddr $boot_start $boot_size
    => abootimg get ver
    => abootimg dump dtb

[1] https://source.android.com/devices/bootloader/boot-image-header
[2] https://source.android.com/devices/architecture/dto/partitions

Signed-off-by: Sam Protsenko 
Signed-off-by: Lokesh Vutla