u-boot.git/cmd/bdinfo.c, branch v2022.01

Merge branch '2021-02-02-drop-asm_global_data-when-unused'

2021-02-15T15:16:45+00:00

- Merge the patch to take  out of

bdinfo: Change to use bdinfo_print_num_ll() where the number could be 64-bit

2021-02-03T10:38:41+00:00

There are some calls to bdinfo_print_num_l() with parameters that
could be a 64-bit value on a 32-bit system. Change those calls to
use bdinfo_print_num_ll() instead.

Signed-off-by: Bin Meng 
Reviewed-by: Simon Glass

bdinfo: Rename function names to be clearer

2021-02-03T10:38:41+00:00

At present we have bdinfo_print_num() to print unsigned long numbers.
We also have print_phys_addr() which accept numbers that might be
64-bit on a 32-bit platform.

Rename these 2 functions to be clearer:

bdinfo_print_num() => bdinfo_print_num_l()
print_phys_addr()  => bdinfo_print_num_ll()

While we are here, make bdinfo_print_num_ll() public so that it can
be used outside cmd/bdinfo.c in the future.

Signed-off-by: Bin Meng

common: Drop asm/global_data.h from common header

2021-02-02T20:33:42+00:00

Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include  at all, so
remove that include.

Signed-off-by: Simon Glass 
Signed-off-by: Tom Rini

x86: video: Show information about each video device

2020-09-25T03:27:27+00:00

At present the 'bdinfo' command shows the framebuffer address, but not the
address of the copy framebuffer, if present. Add support for this.

Signed-off-by: Simon Glass 
Reviewed-by: Bin Meng

cmd: bdinfo: Remove print of superseeded bi_memstart / bi_memsize values

2020-08-26T07:20:00+00:00

Remove printing of the superseeded (by bi_dram[]) memory values from the
bdinfo command.

Signed-off-by: Stefan Roese 
Reviewed-by: Ovidiu Panait

CONFIG_NR_DRAM_BANKS: Remove unreferenced code as its always defined

2020-08-26T07:19:16+00:00

Since commit 86cf1c82850f ("configs: Migrate CONFIG_NR_DRAM_BANKS") &
commit 999a772d9f24 ("Kconfig: Migrate CONFIG_NR_DRAM_BANKS"),
CONFIG_NR_DRAM_BANKS is always defined with a value (4 is default).
It makes no sense to still carry code that is guarded with
"#ifndef CONFIG_NR_DRAM_BANKS" (and similar). This patch removes
all these unreferenced code paths.

Signed-off-by: Stefan Roese 
Reviewed-by: Pali Rohár 
Reviewed-by: Andy Shevchenko 
Reviewed-by: Bin Meng

cmd: bdinfo: Move sram info prints to generic code

2020-08-06T18:26:35+00:00

bi_sramstart and bi_sramsize are generic members of the bd_info structure,
so move the m68k/powerpc-specific prints to generic code. Also, print them
only if SRAM support is enabled via CONFIG_SYS_HAS_SRAM.

Reviewed-by: Simon Glass 
Signed-off-by: Ovidiu Panait

cmd: bdinfo: cleanup phys_addr_t output

2020-08-05T12:18:34+00:00

We currently print the memory size with at least 8 hexadecimal digits.
This creates a ragged output on 64 bit boards, e.g. on a Kendryte K210:

DRAM bank   = 0x0000000000000002
-> start    = 0x0000000080600000
-> size     = 0x0000000000200000
memstart    = 0x0000000000000000
memsize     = 0x00000000
flashstart  = 0x0000000000000000
flashsize   = 0x0000000000000000
flashoffset = 0x0000000000000000

All other numbers are printed with the number of digits needed for the type
ulong. So use this value as minimum number of digits (precision) for
printing physical addresses.

Signed-off-by: Heinrich Schuchardt 
Reviewed-by: Heiko Schocher 
Reviewed-by: Stefan Roese 
Reviewed-by: Simon Glass

lmb/bdinfo: dump lmb info via bdinfo

2020-08-05T03:30:02+00:00

Dump lmb status from the bdinfo command. This is useful for seeing the
reserved memory regions from the u-boot cmdline.

Signed-off-by: Tero Kristo