u-boot.git/cmd/eeprom.c, branch v2024.04

treewide: Tidy up semicolon after command macros

2023-12-13T16:51:24Z

The U_BOOT_CMD_COMPLETE() macro has a semicolon at the end, perhaps inadvertently. Some code has taken advantage of this. Tidy this up by dropping the semicolon from the macro and adding it to macro invocations as required. Signed-off-by: Simon Glass Reviewed-by: Tom Rini Reviewed-by: Ilias Apalodimas

cmd: eeprom: don't truncate target address at 32-bit

2022-11-02T17:58:17Z

On 64-bit platforms where int is 32-bit wide, the eeprom command parse_numeric_param() routine truncates the memory address parameter to the lower 32-bit. Make parse_numeric_param() return long to allow read/write of addresses beyond the lower 4GB. Signed-off-by: Baruch Siach Reviewed-by: Ramon Fried

cmd: eeprom: Do not rewrite EEPROM I2C bus with DM I2C enabled

2022-03-23T06:27:37Z

With DM I2C, the EEPROM bus has been correctly configured in eeprom_execute_command() already. Do not reconfigure it here with hard-coded bus number again. Signed-off-by: Marek Vasut Cc: Heiko Schocher Cc: Tom Rini Reviewed-by: Heiko Schocher

Convert CONFIG_SYS_I2C_SPEED et al to Kconfig

2021-08-30T18:10:07Z

This converts the following to Kconfig: CONFIG_SYS_I2C_SPEED CONFIG_SYS_I2C_SLAVE Signed-off-by: Tom Rini

Convert CONFIG_SYS_I2C_LEGACY to Kconfig and add CONFIG_[ST]PL_SYS_I2C_LEGACY

2021-08-30T18:10:07Z

First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot have SYS_I2C_LEGACY and DM_I2C at the same time, introduce CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only in SPL. Finally, for some PowerPC cases we also need CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to one or more symbols. Signed-off-by: Tom Rini

Convert CONFIG_SYS_I2C_EEPROM_ADDR et al to Kconfig

2021-08-30T18:10:06Z

- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR based on current usage. - Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN, CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS to Kconfig. We move these symbols around a bit and add appropriate dependencies to them. In some cases, we now add a correct default value as well. Signed-off-by: Tom Rini

eeprom: Drop CONFIG_ENV_EEPROM_IS_ON_I2C usage

2021-08-30T18:10:06Z

At this point in time, there's no systems with "U-Boot environment exists on an EEPROM which is accessed over the I2C bus" that sets this option. Drop it. Signed-off-by: Tom Rini

i2c: Rename CONFIG_SYS_I2C to CONFIG_SYS_I2C_LEGACY

2021-07-28T18:29:37Z

It is quite confusing that CONFIG_SYS_I2C selects the legacy I2C and CONFIG_DM_I2C selects the current I2C. The deadline to migrate I2C is less than a year away. Also we want to have a CONFIG_I2C for U-Boot proper just like we have CONFIG_SPL_I2C for SPL, so we can simplify the Makefile rules. Rename this symbol so it is clear it is going away. Signed-off-by: Simon Glass Reviewed-by: Heiko Schocher

dm: i2c: use CONFIG_IS_ENABLED macro for DM_I2C/DM_I2C_GPIO

2021-02-21T05:08:00Z

Use CONFIG_IS_ENABLED() macro, which provides more convenient way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs for both SPL and U-Boot proper. CONFIG_IS_ENABLED(DM_I2C) expands to: - 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y', - 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y', - 0 otherwise. All occurences were replaced automatically using these bash cmds: $ find . -type f -exec sed -i 's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} + $ find . -type f -exec sed -i 's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} + $ find . -type f -exec sed -i 's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} + $ find . -type f -exec sed -i 's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} + $ find . -type f -exec sed -i 's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} + $ find . -type f -exec sed -i 's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} + Reviewed-by: Heiko Schocher Reviewed-by: Simon Glass Signed-off-by: Igor Opaniuk Reviewed-by: Tom Rini Reviewed-by: Priyanka Jain

common: Drop linux/delay.h from common header

2020-05-19T01:19:23Z

Move this uncommon header out of the common header. Signed-off-by: Simon Glass