u-boot.git/cmd, branch v2023.07.01

cmd: CONFIG_CMD_SAVES depends on CONFIG_CMD_LOADS

2023-07-07T20:25:56Z

CONFIG_CMD_SAVES is used to enable support for the "saveenv" command and is only implemented in cmd/load.c when "#if defined(CONFIG_CMD_LOADS)" is met. It is recommended to add dependency constraints to its definition. Prevents "saveenv" command from not being supported when "CONFIG_CMD_SAVES=y CONFIG_CMD_LOADS=n". Suggested-by: Yanjie Ren Signed-off-by: Ying Sun Reviewed-by: Simon Glass

cmd/sbi: display new extensions

2023-07-06T09:28:08Z

OpenSBI already implements some extensions that are not ratified yet: * Debug Console Extension (DBCN) * System Suspend Extension (SUSP) * Collaborative Processor Performance Control Extension (CPPC) Allow the sbi command to display these. Provide the FID definitions of the Debug Console Extension. We can use that extension for an early debug console driver. Signed-off-by: Heinrich Schuchardt Reviewed-by: Leo Yu-Chi Liang

Merge tag 'v2023.07-rc6' into next

2023-07-05T15:28:55Z

Prepare v2023.07-rc6

spl: spl_legacy: Add extra address checks

2023-06-24T17:47:00Z

Check whether the loaded image or entry point does not overlap SPL. Signed-off-by: Marek Vasut

cmd: usb: Prevent reset in usb tree/info command

2023-06-21T11:08:30Z

Commands causing reset in some configs: When bootflow scan is run, this will cause a UCLASS_BOOTDEV device to be added as sibling of those UCLASS_BLK devices found in the search chain defined in environment variable "boot_targets", until boot succeeds from some device. This can happen automatically as part of the default boot process on some boards (example: Rock Pi 4) depending on the board configuration (DISTRO_DEFAULTS, BOOTSTD, BOOTCOMMAND, etc.) because they have bootcmd=bootflow scan. If boot doesn't succeed from any device, and usb is in boot_targets, and an usb storage device is plugged to some usb port at boot time, its UCLASS_MASS_STORAGE device will have a UCLASS_BOOTDEV device as child, besides a UCLASS_BLK child. If once the boot fails the user enters at the U-Boot shell prompt: usb info or usb tree The code in cmd/usb.c will eventually recurse into the UCLASS_BOOTDEV device and pass a null usb_device pointer to usb_show_tree_graph() or usb_show_info() (because it has no parent_priv_). This causes a reset. The expected behaviour would be to ignore the UCLASS_BOOTDEV device, continue listing the usb information and return to the prompt. Minimal test: Another way to trigger this reset as a minimal test or on boards with a different bootcmd would be: - make sure "usb" is in environment variable boot_targets (might need setenv boot_targets usb; and/or saveenv and reset), then, with a usb storage device plugged to a usb port, run: => usb reset ; bootflow scan ; usb info Solution: Fix it (twice) by checking for null parent_priv_ and adding UCLASS_BOOTDEV to the list of ignored class ids before the recursive call. This prevents the current particular problem with UCLASS_BOOTDEV, even in case it ever gets some parent_priv_ struct which is not an usb_device, despite being the child of a usb_device->dev. And it also prevents possible future problems if other children are added to usb devices that don't have parent_priv_ because they are not part of the usb tree, just abstractions of functionality (like UCLASS_BLK and UCLASS_BOOTDEV are now). Signed-off-by: Xavier Drudis Ferran Reviewed-by: Simon Glass Reviewed-by: Marek Vasut Tested-by: Marek Vasut

net: ipv6: Fix CID 453851 and CID 436278

2023-06-14T19:48:45Z

CID 453851 : sprintf() shouldn't copy from/to tmp CID 436278 : DHCP6 option_len should be checked before use Signed-off-by: Sean Edmond Reviewed-by: Ramon Fried

cmd: net: add a 'net stats' command to dump network statistics

2023-06-14T10:40:16Z

Add a new option to the 'net' command which can be used to dump network statistics. To do this, 3 new callbacks are added to the eth_ops structure: .get_sset_count(), .get_strings(), .get_stats(). These callbacks have the same functions as in Linux: to return the number of counters, the strings which describe those counters and the actual values. Signed-off-by: Ioana Ciornei Reviewed-by: Ramon Fried Signed-off-by: Peng Fan

Merge tag 'tpm-for_tom-13062023' of https://source.denx.de/u-boot/custodians/u-boot-tpm into next

2023-06-13T17:14:49Z

tpm autostart

tpm: Add 'tpm autostart' shell command

2023-06-13T05:51:07Z

For a TPM device to be operational we need to initialize it and perform its startup sequence. The 'tpm init' command currently calls tpm_init() which ends up calling the ->open() per-device callback and performs the initial hardware configuration as well as requesting locality 0 for the caller. There no code that currently calls tpm_init() without following up with a tpm_startup() and tpm_self_test_full() or tpm_continue_self_test(). So let's add a 'tpm autostart' command and call tpm_auto_start() which leaves the device in an operational state. It's worth noting that calling tpm_init() only, doesn't allow a someone to use the TPM since the startup sequence is mandatory. We always repeat the pattern of calling - tpm_init() - tpm_startup() - tpm_self_test_full() or tpm_continue_self_test() Reviewed-by: Simon Glass Signed-off-by: Ilias Apalodimas

Merge tag 'xilinx-for-v2023.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next

2023-06-12T20:42:37Z

Xilinx changes for v2023.10-rc1 global: - Use proper U-Boot project name Fix sparse warnings in zynqmp-clk, zynqmp handoff, board cmd: - Cover incorrect 0 length entries Versal NET: - Add bootmode logic - Support SPP production version - Add loadpdi command ZynqMP: - Clear pmufw node command ID handling - Change power domain behavior around zynqmp_pmufw_node() - Fix zynqmp cmd return values and pmufw command - Fix R5 tcm init and modes mmc: - Sync Versal NET emmc DT binding pcie: - Add support for ZynqMP PCIe root port video: - Add support for ZynqMP DP tools: - Fix debug message in relocate-rela