u-boot.git/common/cmd_nand.c, branch v2009.08 Unnamed repository; edit this file 'description' to name the repository. Remove legacy NAND and disk on chip code. 2009-07-17T00:07:47+00:00 Scott Wood scottwood@freescale.com 2009-04-01T20:02:13+00:00 be33b046b549ad88c204c209508cd7657232ffbd Legacy NAND had been scheduled for removal. Any boards that use this were already not building in the previous release due to an #error. The disk on chip code in common/cmd_doc.c relies on legacy NAND, and it has also been removed. There is newer disk on chip code in drivers/mtd/nand; someone with access to hardware and sufficient time and motivation can try to get that working, but for now disk on chip is not supported. Signed-off-by: Scott Wood <scottwood@freescale.com> 
Legacy NAND had been scheduled for removal.  Any boards that use this
were already not building in the previous release due to an #error.

The disk on chip code in common/cmd_doc.c relies on legacy NAND,
and it has also been removed.  There is newer disk on chip code
in drivers/mtd/nand; someone with access to hardware and sufficient
time and motivation can try to get that working, but for now disk
on chip is not supported.

Signed-off-by: Scott Wood <scottwood@freescale.com>
nand/onenand: Fix missing argument checking for "markbad" command 2009-07-07T22:58:05+00:00 Wolfgang Denk wd@denx.de 2009-05-24T15:34:33+00:00 8360b66bac9567701027a0087274d0c9b2fe8d6b The "nand markbad" and "onenand markbad" commands did not check if an argument was passed; if this was forgotten, no error was raised but block 0 was marked as bad. While fixing this bug, clean up the code a bit and allow to pass more than one block address, thus allowing to mark several blocks as bad in a single command invocation. Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Scott Wood <scottwood@freescale.com> 
The "nand markbad" and "onenand markbad" commands did not check if an
argument was passed; if this was forgotten, no error was raised but
block 0 was marked as bad.

While fixing this bug, clean up the code a bit and allow to pass more
than one block address, thus allowing to mark several blocks as bad
in a single command invocation.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
General help message cleanup 2009-06-12T18:47:16+00:00 Wolfgang Denk wd@denx.de 2009-05-24T15:06:54+00:00 a89c33db96a1e55319a286dd4c3c05ca64ac6bfd Many of the help messages were not really helpful; for example, many commands that take no arguments would not print a correct synopsis line, but "No additional help available." which is not exactly wrong, but not helpful either. Commit ``Make "usage" messages more helpful.'' changed this partially. But it also became clear that lots of "Usage" and "Help" messages (fields "usage" and "help" in struct cmd_tbl_s respective) were actually redundant. This patch cleans this up - for example: Before: => help dtt dtt - Digital Thermometer and Thermostat Usage: dtt - Read temperature from digital thermometer and thermostat. After: => help dtt dtt - Read temperature from Digital Thermometer and Thermostat Usage: dtt Signed-off-by: Wolfgang Denk <wd@denx.de> 
Many of the help messages were not really helpful; for example, many
commands that take no arguments would not print a correct synopsis
line, but "No additional help available." which is not exactly wrong,
but not helpful either.

Commit ``Make "usage" messages more helpful.'' changed this
partially. But it also became clear that lots of "Usage" and "Help"
messages (fields "usage" and "help" in struct cmd_tbl_s respective)
were actually redundant.

This patch cleans this up - for example:

Before:
	=> help dtt
	dtt - Digital Thermometer and Thermostat

	Usage:
	dtt         - Read temperature from digital thermometer and thermostat.

After:
	=> help dtt
	dtt - Read temperature from Digital Thermometer and Thermostat

	Usage:
	dtt

Signed-off-by: Wolfgang Denk <wd@denx.de>
Separate mtdparts command from jffs2 2009-04-27T23:06:24+00:00 Ladislav Michl ladis@linux-mips.org 2009-04-21T00:26:31+00:00 0c8a84916c5dacccdc5b27b63fc463e9f3b04f07 On Thu, Mar 19, 2009 at 01:30:36PM +0100, Stefan Roese wrote: > Currently the mtdparts commands are included in the jffs2 command support. > This doesn't make sense anymore since other commands (e.g. UBI) use this > infrastructure as well now. This patch separates the mtdparts commands from > the jffs2 commands making it possible to only select mtdparts when no JFFS2 > support is needed. One more leftover... Let nboot command know about partitions even if JFFS2 support is not enabled. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Acked-by: Stefan Roese <sr@denx.de> 
On Thu, Mar 19, 2009 at 01:30:36PM +0100, Stefan Roese wrote:
> Currently the mtdparts commands are included in the jffs2 command support.
> This doesn't make sense anymore since other commands (e.g. UBI) use this
> infrastructure as well now. This patch separates the mtdparts commands from
> the jffs2 commands making it possible to only select mtdparts when no JFFS2
> support is needed.

One more leftover... Let nboot command know about partitions even if JFFS2
support is not enabled.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Stefan Roese <sr@denx.de>
cmd_nand: drop duplicate NULL ptr check 2009-04-16T21:03:44+00:00 Mike Frysinger vapier@gentoo.org 2009-04-13T02:29:20+00:00 dfc99e143fca44a492918ac6cf3f76ee9c2473a9 The first if statement checks for NULL ptrs, so there is no need to check it again in later else cases (such as .oob). Signed-off-by: Mike Frysinger <vapier@gentoo.org> CC: Scott Wood <scottwood@freescale.com> 
The first if statement checks for NULL ptrs, so there is no need to check
it again in later else cases (such as .oob).

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Scott Wood <scottwood@freescale.com>
Enable multi chip support in the NAND layer 2009-03-23T20:53:37+00:00 Wolfgang Grandegger wg@grandegger.com 2009-02-11T17:38:20+00:00 672ed2aee91b4856f6671fc72cd34168d8f1b624 This patch adds support for NAND_MAX_CHIPS to the MTD NAND layer. Multi-chips devices are displayed as shown: Device 0: 2x NAND 512MiB 3,3V 8-bit, sector size 128 KiB Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com> 
This patch adds support for NAND_MAX_CHIPS to the MTD NAND layer.
Multi-chips devices are displayed as shown:

  Device 0: 2x NAND 512MiB 3,3V 8-bit, sector size 128 KiB

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Separate mtdparts command from jffs2 2009-03-20T21:39:14+00:00 Stefan Roese sr@denx.de 2009-03-19T12:30:36+00:00 68d7d65100e84df00bca971c114092731b441090 Currently the mtdparts commands are included in the jffs2 command support. This doesn't make sense anymore since other commands (e.g. UBI) use this infrastructure as well now. This patch separates the mtdparts commands from the jffs2 commands making it possible to only select mtdparts when no JFFS2 support is needed. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> 
Currently the mtdparts commands are included in the jffs2 command support.
This doesn't make sense anymore since other commands (e.g. UBI) use this
infrastructure as well now. This patch separates the mtdparts commands from
the jffs2 commands making it possible to only select mtdparts when no JFFS2
support is needed.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
NAND: Have nboot accept .e and .i as legacy no-ops. 2009-03-17T17:06:04+00:00 Scott Wood scottwood@freescale.com 2009-03-17T17:06:04+00:00 65d8bc94d8214812ccdf3372d3fef845cf4ec2e5 This was intended to happen before, but a trivial bug prevented it. Signed-off-by: Scott Wood <scottwood@freescale.com> 
This was intended to happen before, but a trivial bug prevented it.

Signed-off-by: Scott Wood <scottwood@freescale.com>
NAND: Make nboot skip bad blocks 2009-03-17T17:04:22+00:00 Ladislav Michl ladis@linux-mips.org 2009-03-13T13:38:19+00:00 0987505540918b2464b73069af3a5b766dbd3ceb nboot command currently does not skip bad blocks and gives read error when loading image stored over bad block. With patch applied, nboot works as expected: Device 0 bad blocks: 00780000 014a0000 02000000 02cc0000 04aa0000 Loading from NAND 128MiB 3,3V 8-bit, offset 0x2c00000 Image Name: Linux-2.6.22-omap1 Created: 2008-11-20 23:44:32 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1052520 Bytes = 1 MB Load Address: 10008000 Entry Point: 10008000 Skipping bad block 0x02cc0000 Automatic boot of image at addr 0x10400000 ... ... Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Scott Wood <scottwood@freescale.com> 
nboot command currently does not skip bad blocks and gives read error when
loading image stored over bad block. With patch applied, nboot works as
expected:

Device 0 bad blocks:
  00780000
  014a0000
  02000000
  02cc0000
  04aa0000

Loading from NAND 128MiB 3,3V 8-bit, offset 0x2c00000
   Image Name:   Linux-2.6.22-omap1
   Created:      2008-11-20  23:44:32 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1052520 Bytes =  1 MB
   Load Address: 10008000
   Entry Point:  10008000
Skipping bad block 0x02cc0000
Automatic boot of image at addr 0x10400000 ...
...

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Command usage cleanup 2009-01-28T07:49:52+00:00 Peter Tyser ptyser@xes-inc.com 2009-01-28T00:03:12+00:00 2fb2604d5c20beb061b0a94282b7f6eb14d00cb8 Remove command name from all command "usage" fields and update common/command.c to display "name - usage" instead of just "usage". Also remove newlines from command usage fields. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> 
Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>