u-boot.git/common/spl/Kconfig, branch v2017.11

spl: set SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to 0x4000 for rockchip

2017-11-07T08:16:57+00:00

Rockchip use a 'loader2' partition for U-Boot, so u-boot.bin or
u-boot.itb load by SPL need to locate at0x4000. Detail here:
http://opensource.rock-chips.com/wiki_Boot_option

Signed-off-by: Kever Yang 
Acked-by: Philipp Tomsich 
Reviewed-by: Philipp Tomsich

TI: ARCH_OMAP2PLUS: Enable SPL_STACK_R and provide default value

2017-09-29T18:07:51+00:00

On ARCH_OMAP2PLUS platforms we know what the DDR layout is going to be,
and that it is safe to use SPL_STACK_R and provide a default value for
it.  select this and re-sync the defconfigs.

Signed-off-by: Tom Rini

spl: typo fix for SPL_ATF_SUPPORT description

2017-09-07T14:44:38+00:00

Delete one redundant 'which' for SPL_ATF_SUPPORT description.

Signed-off-by: Kever Yang

spl: add serial download protocol (SDP) support

2017-08-23T08:41:58+00:00

Add USB serial download protocol support to SPL. If the SoC started
in recovery mode the SPL will immediately switch to SDP and wait for
further downloads/commands from the host side.

Signed-off-by: Stefan Agner 
Reviewed-by: Stefano Babic 
Reviewed-by: Łukasz Majewski

env: Rename getenv/_f() to env_get()

2017-08-16T12:30:24+00:00

We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.

Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.

Suggested-by: Wolfgang Denk 
Signed-off-by: Simon Glass

env: Rename setenv() to env_set()

2017-08-16T12:22:18+00:00

We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.

Suggested-by: Wolfgang Denk 
Signed-off-by: Simon Glass

dm: timer: normalise SPL and TPL support

2017-08-13T15:12:36+00:00

To fully support DM timer in SPL and TPL, we need a few things cleaned
up and normalised:
- inclusion of the uclass and drivers should be an all-or-nothing
  decision for each stage and under control of $(SPL_TPL_)TIMER
  instead of having the two-level configuration with TIMER and
  $(SPL_TPL_)TIMER_SUPPORT
- when $(SPL_TPL_)TIMER is enabled, the ARMv8 generic timer code can
  not be compiled in

This normalises configuration to $(SPL_TPL_)TIMER and moves the config
options to drivers/timer/Kconfig (and cleans up the collateral damage
to some defconfigs that had SPL_TIMER_SUPPORT enabled).

Signed-off-by: Philipp Tomsich 
Reviewed-by: Simon Glass

moveconfig: migrate TPL_STACK, TPL_TEXT_BASE and TPL_MAX_SIZE

2017-08-13T15:12:35+00:00

We can finally drop TPL_STACK, TPL_TEXT_BASE and TPL_MAX_SIZE off the
whitelist (this time it's really happening!) and migrate the setting
(only used on the RK3368-uQ7 so far) into Kconfig.

Signed-off-by: Philipp Tomsich 
Reviewed-by: Simon Glass

spl: support TPL_STACK, TPL_MAX_SIZE and TPL_TEXT_BASE via Kconfig

2017-08-13T15:12:34+00:00

Let's clean up behind ourselves and move the (newly defined)
TPL_STACK, TPL_MAX_SIZE and TPL_TEXT_BASE into Kconfig.  Given that
0x0 might be considered to be valid values for TPL_TEXT_BASE and
TPL_STACK, we need to introduce helper config options
("TPL_NEEDS_SEPARATE_...") to indicate that these symbols are used
(and not inherited from their SPL variants) for any given
target-platform.

Signed-off-by: Philipp Tomsich 
Reviewed-by: Simon Glass

spl: Kconfig: migrate $(SPL_TPL_)LDSCRIPT to Kconfig

2017-08-13T15:12:34+00:00

Now that we have split up SPL_LDSCRIPT into a SPL and TPL variant and
have started to use the TPL-variant for the RK3368, it's time to clean
up behind ourselves: move both variants into Kconfig and remove them
from the whitelist.

Signed-off-by: Philipp Tomsich 
Reviewed-by: Simon Glass