u-boot.git/common/spl/Kconfig, branch v2020.10

fs/squashfs: new filesystem

2020-08-08T02:31:32Z

Add support for SquashFS filesystem. Right now, it does not support compression but support for zlib will be added in a follow-up commit. Signed-off-by: Joao Marcos Costa

spi: Allow separate control of SPI_FLASH_TINY for SPL/TPL

2020-08-04T02:19:54Z

In some cases SPL needs to be able to erase but TPL just needs to read. Allow these to have separate settings for SPI_FLASH_TINY. Signed-off-by: Simon Glass

Convert CONFIG_SYS_MMCSD_FS_BOOT_PARTITION to Kconfig

2020-07-28T20:18:10Z

This converts the following to Kconfig: CONFIG_SYS_MMCSD_FS_BOOT_PARTITION Signed-off-by: Adam Ford

Convert CONFIG_SPL_NAND_BASE et al to Kconfig

2020-07-28T20:18:10Z

This converts the following to Kconfig: CONFIG_SPL_NAND_BASE CONFIG_SPL_NAND_IDENT Signed-off-by: Adam Ford

Convert CONFIG_SPL_NAND_DRIVERS et al to Kconfig

2020-07-28T20:18:10Z

This converts the following to Kconfig: CONFIG_SPL_NAND_DRIVERS CONFIG_SPL_NAND_ECC CONFIG_SPL_NAND_SIMPLE Signed-off-by: Adam Ford

spi: Convert CONFIG_DM_SPI* to CONFIG_$(SPL_TPL_)DM_SPI*

2020-06-29T17:34:43Z

This change allows more fine tuning of driver model based SPI support in SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI support in SPL and TPL via Kconfig option. Before this change it was necessary to use: /* SPI Flash Configs */ #if defined(CONFIG_SPL_BUILD) #undef CONFIG_DM_SPI #undef CONFIG_DM_SPI_FLASH #undef CONFIG_SPI_FLASH_MTD #endif in the ./include/configs/.h, which is error prone and shall be avoided when we strive to switch to Kconfig. The goal of this patch: Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL). Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must still support non DM driver. Another use case is the conversion of non DM/DTS SPI driver to support DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the distinction is needed in Kconfig (also if SPL version of the driver supports OF_PLATDATA). In the end of the day one would have to support following use cases (in single driver file - e.g. mxs_spi.c): - U-Boot proper driver supporting DT/DTS - U-Boot proper driver without DT/DTS support (deprecated) - SPL driver without DT/DTS support - SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to run full blown DT/DTS) - SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained environment with no fitImage and OF_LIBFDT support). Some boards do require SPI support (with DM) in SPL (TPL) and some only have DM_SPI{_FLASH} defined to allow compiling SPL. This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI) and provides corresponding defines in Kconfig. Signed-off-by: Lukasz Majewski Tested-by: Adam Ford #da850-evm Signed-off-by: Hou Zhiqiang [trini: Fixup a few platforms] Signed-off-by: Tom Rini

Add support for SHA384 and SHA512

2020-06-12T17:14:07Z

The current recommendation for best security practice from the US government is to use SHA384 for TOP SECRET [1]. This patch adds support for SHA384 and SHA512 in the hash command, and also allows FIT images to be hashed with these algorithms, and signed with sha384,rsaXXXX and sha512,rsaXXXX The SHA implementation is adapted from the linux kernel implementation. [1] Commercial National Security Algorithm Suite http://www.iad.gov/iad/programs/iad-initiatives/cnsa-suite.cfm Signed-off-by: Reuben Dowle

sifive: fu540: Add U-Boot proper sector start

2020-06-04T01:44:09Z

Add U-Boot proper sector start offset for SiFive FU540. This value is based on the partition layout supported by SiFive FU540. u-boot.itb need to write on this specific offset so-that the SPL will retrieve it from here and load. Signed-off-by: Jagan Teki Reviewed-by: Bin Meng Reviewed-by: Pragnesh Patel

rename symbol: CONFIG_TEGRA -> CONFIG_ARCH_TEGRA

2020-05-15T18:47:35Z

Have this symbol follow the pattern of all other such symbols. Signed-off-by: Trevor Woerner

spl: sdp: Add CONFIG_SPL_SDP_USB_DEV for USB device

2020-05-03T13:31:41Z

Add a new configuration CONFIG_SPL_SDP_USB_DEV to specify the usb index for spl sdp driver, so that we change use different device. The default value is 0. Signed-off-by: Ye Li Signed-off-by: Peng Fan