u-boot.git/common/spl/Kconfig, branch v2021.01

Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-sunxi

2020-10-23T00:32:02Z

- sun8i emac changes (Andre) - SCP firmware (Samuel)

Kconfig: Use hex values for CONFIG_{SPL,TPL}_SIZE_LIMIT

2020-10-22T13:54:52Z

CONFIG_{SPL,TPL}_SIZE_LIMIT are defined as hex (SPL_SIZE_LIMIT was converted in b51882d0 ("spl: Convert CONFIG_SPL_SIZE_LIMIT to hex"), but there are still places that reference integer values. Change those to hex as well. Also, update the Makefile to check for 0x0 instead of 0. This also fixes the following build error when CONFIG_SPL_SIZE_LIMIT is set by menuconfig to 0x0: ... spl/u-boot-spl.bin exceeds file size limit: limit: 0 bytes actual: 0x80f0 bytes excess: 0x80f0 bytes Signed-off-by: Ovidiu Panait Reviewed-by: Simon Glass

spl: fit: Minimally parse OS properties with FIT_IMAGE_TINY

2020-10-22T06:13:43Z

Some boards, specifically 64-bit Allwinner boards (sun50i), are extremely limited on SPL size. One strategy that was used to make space was to remove the FIT "os" property parsing code, because it uses a rather large lookup table. However, this forces the legacy FIT parsing code path, which requires the "firmware" entry in the FIT to reference the U-Boot binary, even if U-Boot is not the next binary in the boot sequence (for example, on sun50i boards, ATF is run first). This prevents the same FIT image from being used with a SPL with CONFIG_SPL_FIT_IMAGE_TINY=n and CONFIG_SPL_ATF=y, because the boot method selection code looks at `spl_image.os`, which is only set from the "firmware" entry's "os" property. To be able to use CONFIG_SPL_ATF=y, the "firmware" entry in the FIT must be ATF, and U-Boot must be a loadable. For this to work, we need to parse the "os" property just enough to tell U-Boot from other images, so we can find it in the loadables list to append the FDT, and so we don't try to append the FDT to ATF (which could clobber adjacent firmware). So add the minimal code necessary to distinguish U-Boot/non-U-Boot loadables with CONFIG_SPL_FIT_IMAGE_TINY=y. This adds about 300 bytes, much less than the 7400 bytes added by CONFIG_SPL_FIT_IMAGE_TINY=n. Acked-by: Patrick Wildt Signed-off-by: Samuel Holland Reviewed-by: Jagan Teki

spl: Add SPL_SERIAL as requirement for SDP_USB_SDP

2020-10-14T15:16:34Z

The USB SDP protocol require the SPL serial support to allow the build to succeed. Signed-off-by: Otavio Salvador

spl: Kconfig: Record proper dependency for SPL_ATF

2020-09-23T08:31:41Z

ATF support was all the time based on FIT image support but this dependency is not recorded anywhere. For !SPL_FIT && SPL_ATF there is compilation error: common/spl/spl.c: In function 'board_init_r': common/spl/spl.c:689:26: error: 'struct spl_image_info' has no member named 'fdt_addr' 689 | spl_fixup_fdt(spl_image.fdt_addr); Signed-off-by: Michal Simek

fpga: kconfig: Rename SPL_FPGA_SUPPORT to SPL_FPGA

2020-09-23T08:31:41Z

The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile and zynqmp.c to simplify if/endif logic in zynqmp.c. This change is mostly done to be able to use CONFIG_IS_ENABLED macro and obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync. And removing one line from Topic Miami boards which is not needed because symbol is not enabled via Kconfig. Signed-off-by: Michal Simek Reviewed-by: Simon Glass

fs/squashfs: new filesystem

2020-08-08T02:31:32Z

Add support for SquashFS filesystem. Right now, it does not support compression but support for zlib will be added in a follow-up commit. Signed-off-by: Joao Marcos Costa

spi: Allow separate control of SPI_FLASH_TINY for SPL/TPL

2020-08-04T02:19:54Z

In some cases SPL needs to be able to erase but TPL just needs to read. Allow these to have separate settings for SPI_FLASH_TINY. Signed-off-by: Simon Glass

Convert CONFIG_SYS_MMCSD_FS_BOOT_PARTITION to Kconfig

2020-07-28T20:18:10Z

This converts the following to Kconfig: CONFIG_SYS_MMCSD_FS_BOOT_PARTITION Signed-off-by: Adam Ford

Convert CONFIG_SPL_NAND_BASE et al to Kconfig

2020-07-28T20:18:10Z

This converts the following to Kconfig: CONFIG_SPL_NAND_BASE CONFIG_SPL_NAND_IDENT Signed-off-by: Adam Ford