First set of u-boot-atmel fixes for 2019.07 cycle

When introduced this limit was an int but was then changed to hex
without noting as much in the prompt nor changing existing users.  Put
this back to an int.

Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Fixes: 2577015dc5c4 ("spl: add overall SPL size check")
Signed-off-by: Tom Rini <trini@konsulko.com>

This adds a size check for SPL that can dynamically check generated
SPL binaries (including devicetree) for a size limit that ensures
this image plus global data, heap and stack fit in initial SRAM.

Since some of these sizes are not available to make, a new host tool
'spl_size_limit' is added that dumps the resulting maximum size for
an SPL binary to stdout. This tool is used in toplevel Makefile to
implement the size check on SPL binaries.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

By default the configuration of the PMC is to have an external crystal
connected that requires driving on both XIN and XOUT pins.
The bypass configuration means that only XIN will be used, the SoC will not
do any driving, and the XIN needs to be provided with a proper signal.
This is the MOSCXTBY bit in the PMC main clock generator register.
The SPL needs to properly initialize the PMC registers before switching
to external clock signal and raising the clock to the cruise speed.

Also created Kconfig for this specific configuration.
By default this is disabled.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>

Set the spl_image->fdt_addr pointer both for simple fitImage configuration
as well as full fitImage configuration, to let spl_perform_fixups() access
the DT and perform modifications to it if necessary.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>

Signed-off-by: Vagrant Cascadian <vagrant@debian.org>

FIT_IMAGE_TINY is used to reduce the size of the SPL by removing os-type
tracking and recording the loadables into the loaded FDT. When this option
is enabled, it is assumed that the next stage firmware is u-boot.
However this does not play well with the SPL_OS_BOOT option that enables
loading different type of next stage firmware, like the OS itself.

When SPL_OS_BOOT is used, do not disable os-tracking. The added footprint
is about 300 Bytes.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

This patch tries to implement a generic watchdog_reset() function that
can be used by all boards that want to service the watchdog device in
U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG.

Without this approach, new boards or platforms needed to implement a
board specific version of this functionality, mostly copy'ing the same
code over and over again into their board or platforms code base.

With this new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).

This patch also adds a new flag to the GD flags, to flag that the
watchdog is ready to use and adds the pointer to the watchdog device
to the GD. This enables us to remove the global "watchdog_dev"
variable, which was prone to cause problems because of its potentially
very early use in watchdog_reset(), even before the BSS is cleared.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Maxim Sloyko <maxims@google.com>
Cc: Erik van Luijk <evanluijk@interact.nl>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: "Álvaro Fernández Rojas" <noltari@gmail.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)

This patch adds a short message to the SPL NAND loader, which displays
the source and destinations addresses including the size of the
loaded image, like this:

U-Boot SPL 2019.04-rc3-00113-g486efd8aaf (Mar 15 2019 - 14:18:02 +0100)
Trying to boot from NAND
Loading U-Boot from 0x00040000 (size 0x000a0000) to 0x22900000

I find this message quite helpful - hopefully others do so as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>