The call to spl_mmc_get_uboot_raw_sector() completely ignores and
overwrites the raw_sect value passed from the caller of spl_mmc_load().

Fix this by passing raw_sect to the function and returning the same
value in the default case.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

- Libre Computer ALL-H3-IT/ALL-H5-CC board (Chen-Yu Tsai)
- Allwinner R40 Ethernet, usb phy enablement (Andre Przywara)
- Sunxi auto load from 128KB MMC offset (Andre Przywara)
- Orange Pi Win Ethernet phy enablement (Jernej Skrabec)

For Allwinner SoCs the CONFIG_SYS_SPI_U_BOOT_OFFS value is not really a
board choice: The boot ROM only loads the SPL from offset 0 of the SPI
NOR flash, and loads at most 32KB. This is a similar situation as on MMC,
so consequently we create our "joint" image (SPL + U-Boot proper) with
that 32KB offset during the build.

So define the value of this symbol to be 32KB by default for every
Allwinner SoC. This removes the definition of this symbol from the
_defconfig files, and avoids every board to define this over and over
again.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>

These global variables are quite short and generic. In fact the same name
is more often used locally for struct members and function arguments.

Add a image_ prefix to make them easier to distinguish.

Signed-off-by: Simon Glass <sjg@chromium.org>

Allow reading compressed content from fit image, even if
CONFIG_SPL_OS_BOOT is not set.

This allow booting compressed 2nd stage u-boot from fit image.

Additionally, do not print warning message if compression node is not
found, since it simply implies the content is uncompressed.

Signed-off-by: Klaus H. Sorensen <khso@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>

At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>

These global variables are quite short and generic. In fact the same name
is more often used locally for struct members and function arguments.

Add a image_ prefix to make them easier to distinguish.

Signed-off-by: Simon Glass <sjg@chromium.org>

- Clearfog: Fix SD booting (Baruch)
- Misc updates to MMC handling in SPL to support booting from
  main data partition (vs hardware boot partition) on MVEBU (Baruch)

Xilinx/FPGA changes for v2020.04

ARM64:
- Add INIT_SPL_RELATIVE dependency

SPL:
- FIT image fix
- Enable customization of bl2_plat_get_bl31_params()

Pytest:
- Add test for octal/hex conversions

Microblaze:
- Fix manual relocation for one SPI instance

Nand:
- Convert zynq/zynqmp drivers to DM

Xilinx:
- Enable boot script location via Kconfig
- Support OF_SEPARATE in board FDT selection
- Remove low level uart setup it is done later by code
- Add support for DEVICE_TREE variable passing for SPL

Zynq:
- Enable jtag boot mode via distro boot
- Removing unused baseaddresses from hardware.h
- DT fixups

ZynqMP:
- Fix emmc boot sequence
- Simplify spl logic around bss and board_init_r()
- Support psu_post_config_data() calling
- Tune mini-nand DTS
- Fix psu wiring for a2197 boards
- Add runtime MMC device boot order filling in spl
- Clear ATF handoff handling with custom bl2_plat_get_bl31_params()
- Add support u-boot.its generation
- Use single image configuration for all platforms
- Enable PANIC_HANG via Kconfig
- DT fixups
- Firmware fixes
- Add support for zcu208 and zcu1285

Versal:
- Fix emmc boot sequence
- Enable board_late_init() by default