If we don't want to build support for any partition types we can now
add #undef CONFIG_PARTITIONS in a board config file to keep this from
being compiled in. Otherwise boards assume this is compiled in by
default

Signed-off-by: Matthew McClintock <msm@freescale.com>

Signed-off-by: Loïc Minier <loic.minier@linaro.org>

The reset request in usb_stor_get_info is causing issues with some usb
sticks. Some of these sticks vendor_id/product_id have been hardcoded to
not reset but better is to remove the reset altogether. It is not needed.

Signed-off-by: Erik Hansen <erik@makarta.com>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This patch changes `usb_stor_scan' to scan all the LUNs of each mass
storage device.  It also fixes the various commands to correctly set
the LUN field.

Notably, it allows each LUN of GuruPlug's microSD card reader to be
accessed.

Signed-off-by: Ludovic Courtès <ludo@gnu.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>

The dots printed by common/usb_storage.c as progress meter corrupt the
output for example of "fatls usb" commands like this:

=> fatls usb 0
.			<<==== here
       29   file.001
       29   file.002
       29   file.003
       29   file.004
       29   file.005
       29   file.006
       29   file.007
       29   file.008
       29   file.009
       29   file.010
       29   file.011
       29   file.012
       29   file.013
       29   file.014
       29   file.015
       29   file.016
.			<<==== here
       29   file.017
       29   file.018
       29   file.019
...

Turn the progress output into a debug message.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>

The device type was left uninitialized which caused later tests
against DEV_TYPE_UNKNOWN to fail. In the result, "usb part" would
attempt to print information about non-existent devices like this:

	=> usb part
	print_part of 0

	Partition Map for USB device 0  --   Partition Type: DOS

	Partition     Start Sector     Num Sectors     Type
	    1                    0         2031616      f8

	print_part of 1
	## Unknown partition table

	print_part of 2
	## Unknown partition table

	print_part of 3
	## Unknown partition table

	print_part of 4
	## Unknown partition table
	=>

By initializing the type as DEV_TYPE_UNKNOWN we avoid all the
"Unknown partition table" messages.

[Note: the "print_part of ?" messages is left over debug code that
will be removed in another patch.]

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>

While debugging one ill behaving USB device I found two bugs in USB
storage probe.

usb_stor_get_info() returns -1 (error), 0 (skip) or 1 (ok). First part
of this patch fixes error case.

Second part fixes usb_inquiry()'s retry counter handling. Original code
had retry = -1 on error case, not retry = 0 as checked in the next line.

Signed-off-by: Kim B. Heino <Kim.Heino@bluegiga.com>

Here's another USB storage patch. Currently U-Boot handles storage
devices #0 - #4 as valid devices, even if there is none connected. This
patch fixes usb_stor_get_dev() to check detected device count instead
of MAX-define.

This is very important for ill behaving devices. usb_dev_desc[] can be
partially initialized if device probe fails.

After fixing get_dev() it was easy to fix "usb part" etc commands.
Previously it outputed "Unknown partition table" five times, now it's
"no USB devices available".

Signed-off-by: Kim B. Heino <Kim.Heino@bluegiga.com>

This patch implements write support to usb device with raw partition.
It will be useful for filesystem write support to usb device from
u-boot in future.

Tested with writing kernel image to raw usb disk & booting with usb
read command into ram.

[Note:  run usb part to get info about start sector & number of
sectors on a partition for usb write operation.]

Signed-off-by: Mahavir Jain <mjain@marvell.com>