Add callback with __weak annotation to allow setup of environment
partition number in runtime from a board file.

Propagate mmc_switch_part() return value into init_mmc_for_env() instead
of -1 in case of failure.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>

Some architecture needs extra device tree setup. Instead of adding
yet another hook, convert arch_fixup_memory_node to be a generic
FDT fixup function.

[maz: collapsed 3 patches into one, rewrote commit message]

Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

Use CONFIG_SOC_KEYSTONE in common places instead of defining
a lot of "if def .. || if def " for different Keystone2 SoC types.

Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>

For sandbox we have a fallback console which is used very early in
U-Boot, before serial drivers are available. Rather than try to guess
when to switch to the real console, add a flag so we can be sure. This
makes sure that sandbox can always output a panic() message, for example,
and avoids silent failure (which is very annoying in sandbox).

Signed-off-by: Simon Glass <sjg@chromium.org>

If the console is not present, we try to reduce overhead by stopping any
output in vprintf(), before it gets to putc(). This is of dubious merit
in general, but in the case of sandbox it is incorrect since we have a
fallback console which reports errors very early in U-Boot. If this is
defeated U-Boot can hang or exit with no indication of what is wrong.

Remove the optimisation for sandbox.

Signed-off-by: Simon Glass <sjg@chromium.org>

The current functions for adding and removing devices require a device name.
This is not convenient for driver model, which wants to store a pointer to
the relevant device. Add new functions which provide this feature and adjust
the old ones to call these.

Signed-off-by: Simon Glass <sjg@chromium.org>

Initialise devices marked 'pre-reloc' and make them available prior to
relocation. Note that this requires pre-reloc malloc() to be available.

Signed-off-by: Simon Glass <sjg@chromium.org>

Driver model currently only operates after relocation is complete. In this
state U-Boot typically has a small amount of memory available. In adding
support for driver model prior to relocation we must try to use as little
memory as possible.

In addition, on some machines the memory has not be inited and/or the CPU
is not running at full speed or the data cache is off. These can reduce
execution performance, so the less initialisation that is done before
relocation the better.

An immediately-obvious improvement is to only initialise drivers which are
actually going to be used before relocation. On many boards the only such
driver is a serial UART, so this provides a very large potential benefit.

Allow drivers to mark themselves as 'pre-reloc' which means that they will
be initialised prior to relocation. This can be done either with a driver
flag or with a 'dm,pre-reloc' device tree property.

To support this, the various dm scanning function now take a 'pre_reloc_only'
parameter which indicates that only drivers marked pre-reloc should be
bound.

Signed-off-by: Simon Glass <sjg@chromium.org>

At present stdio device functions do not get any clue as to which stdio
device is being acted on. Some implementations go to great lengths to work
around this, such as defining a whole separate set of functions for each
possible device.

For driver model we need to associate a stdio_dev with a device. It doesn't
seem possible to continue with this work-around approach.

Instead, add a stdio_dev pointer to each of the stdio member functions.

Note: The serial drivers have the same problem, but it is not strictly
necessary to fix that to get driver model running. Also, if we convert
serial over to driver model the problem will go away.

Code size increases by 244 bytes for Thumb2 and 428 for PowerPC.

22: stdio: Pass device pointer to stdio methods
       arm: (for 2/2 boards)  all +244.0  bss -4.0  text +248.0
   powerpc: (for 1/1 boards)  all +428.0  text +428.0

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>