u-boot.git/common, branch v2018.01-rc2

common: image.c: Fix CACHE: Misaligned operation output

2017-12-18T18:06:30+00:00

When booting a itb file with a Ramdisk on a imx6 based
board, U-Boot drops the warning:

Loading Kernel Image ... OK
Loading Ramdisk to 4ecf1000, end 4ef8b11f ... \
CACHE: Misaligned operation at range [4ecf1000,  4ef8b11f]

Fix it!

Signed-off-by: Heiko Schocher 
Tested-by: Ayoub Zaki

Merge tag 'xilinx-for-v2018.01-rc2-v2' of git://www.denx.de/git/u-boot-microblaze

2017-12-18T17:23:27+00:00

Xilinx changes for v2018.01-rc2-v2

fpga:
- Enable loading bitstream via fit image for !xilinx platforms

zynq:
- Fix SPL SD boot mode

zynqmp:
- Not not reset in panic
- Do not use simple allocator because of fat changes
- Various dt chagnes
- modeboot variable setup
- Fix fpga loading on automotive devices
- Fix coverity issues

test:
- Fix env test for !hush case - Stephen's patch

Merge git://git.denx.de/u-boot-dm

2017-12-14T20:46:07+00:00

fpga: allow programming fpga from FIT image for all FPGA drivers

2017-12-14T15:09:39+00:00

This drops the limit that fpga is only loaded from FIT images for Xilinx.
This is done by moving the 'partial' check from 'common/image.c' to
'drivers/fpga/xilinx.c' (the only driver supporting partial images yet)
and supplies a weak default implementation in 'drivers/fpga/fpga.c'.

Signed-off-by: Simon Goldschmidt 
Tested-by: Michal Simek  (On zcu102)
Signed-off-by: Michal Simek

binman: Add binman support to spl_ram.c

2017-12-13T02:53:45+00:00

SPL supports reading U-Boot from a RAM location. At present this is
hard-coded to the U-Boot text base address. Use binman to allow this to
come from the image file, if binman is used.

Signed-off-by: Simon Glass

binman: Add binman symbol support to SPL

2017-12-13T02:53:45+00:00

Allow SPL to access binman symbols and use this to get the address of
U-Boot. This falls back to CONFIG_SYS_TEXT_BASE if the binman symbol
is not available.

Signed-off-by: Simon Glass

SPL: Add FIT data-position property support

2017-12-13T02:33:38+00:00

For external data, FIT has a optional property "data-position" which
can set the external data to a fixed offset to FIT beginning.
Add the support for this property in SPL FIT.

Signed-off-by: Ye Li 
Signed-off-by: Peng Fan 
Reviewed-by: Simon Glass 
Reviewed-by: Tomas Melin 
Cc: Pantelis Antoniou 
Cc: "Andrew F. Davis" 
Cc: Igor Grinberg 
Cc: "tomas.melin@vaisala.com" 
Cc: Kever Yang 
Cc: Andre Przywara 
Cc: York Sun 
Cc: Lokesh Vutla 
Cc: "Cooper Jr., Franklin" 
Cc: George McCollister 
Cc: Tuomas Tynkkynen 
Cc: Jean-Jacques Hiblot 
Cc: Rick Altherr 
Cc: Tom Rini 
Reviewed-by: Lokesh Vutla 
Reviewed-by: York Sun

log: Plumb logging into the init sequence

2017-12-07T20:17:00+00:00

Set up logging both before and after relocation.

Signed-off-by: Simon Glass 
Reviewed-by: Bin Meng

log: Add a test command

2017-12-07T20:17:00+00:00

Add a command which exercises the logging system.

Signed-off-by: Simon Glass

log: Add a console driver

2017-12-07T20:17:00+00:00

It is useful to display log messages on the console. Add a simple driver
to handle this.

Note that this driver outputs to the console, which may be serial or
video. It does not specifically select serial output.

Signed-off-by: Simon Glass 
Reviewed-by: Bin Meng