- Add support for rockchip SoC: PX30, RK3308
- Add and migrate to use common dram driver: PX30, RK3328, RK3399
- Add rk3399 board Tinker-s support
- Board config update for Rock960, Rockpro64

Right now enabling SPL_FRAMEWORK will also enable it for the TPL in all
cases, making the TPL bigger. There may be cases where the TPL is really
size constrained due to its underlying ram size.

Therefore introduce a new TPL_FRAMEWORK option and make the relevant
conditionals check for both. The default is set to "y if SPL_FRAMEWORK"
to mimic the previous behaviour where the TPL would always get the
SPL framework if it was enabled in SPL.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

The loading convention for optee or any other tee on arm64 is as bl32
parameter to the trusted-firmware. So TF-A gets invoked with the TEE as
bl32 and main u-boot as bl33. Once it has done its startup TF-A jumps
into the bl32 for the TEE startup, returns to TF-A and then jumps to bl33.

All of them get passed a devicetree as parameter and all components often
get loaded from a FIT image.

OP-TEE will create additional nodes in that devicetree namely a firmware
node and possibly multiple reserved-memory nodes.

While this devicetree is used in main u-boot, in most cases it won't be
the one passed to the actual kernel. Instead most boot commands will load
a new devicetree from somewhere like mass storage of the network, so if
that happens u-boot should transfer the optee nodes to that new devicetree.

To make that happen introduce optee_copy_fdt_nodes() called from the dt
setup function in image-fdt which after checking for the optee presence
in the u-boot dt will make sure a optee node is present in the kernel dt
and transfer any reserved-memory regions it can find.

Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>

- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.

Trusted-Firmware can also initialize a secure payload to use as a trusted
execution environment. In general for the arm64 case this is provided as
separate image and uboot is supposed to also place it in a predetermined
location in memory and add the necessary parameters to the ATF boot params.

So add the possibility to get this tee payload from the provided FIT image
and setup things as necessary.

Tested on a Rockchip PX30 with mainline TF-A, mainline OP-Tee (with pending
PX30 support) and mainline 5.4-rc1 Linux kernel.

Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

'make tests' on a 32bit ARM system leads to

In file included from ../common/cli_hush.c:79:
../include/malloc.h:364:7: error: conflicting types for ‘memset’
 void* memset(void*, int, size_t);
       ^~~~~~
In file included from ../include/compiler.h:126,
                 from ../include/env.h:12,
                 from ../common/cli_hush.c:78:
../include/linux/string.h:103:15:
note: previous declaration of ‘memset’ was here
 extern void * memset(void *,int,__kernel_size_t);
               ^~~~~~
In file included from ../common/cli_hush.c:79:
../include/malloc.h:365:7: error: conflicting types for ‘memcpy’
 void* memcpy(void*, const void*, size_t);
       ^~~~~~
In file included from ../include/compiler.h:126,
                 from ../include/env.h:12,
                 from ../common/cli_hush.c:78:
../include/linux/string.h:106:15:
note: previous declaration of ‘memcpy’ was here
 extern void * memcpy(void *,const void *,__kernel_size_t);
        ^~~~~~

According to the U-Boot coding style guide common.h should be the first
include.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

When full malloc is enabled and SYS_MALLOC_F is also enabled, the simple
pre-reloc heap is used before relocation. In this case, calloc() uses
the MALLOC_ZERO macro to zero out the allocated memory. However, since
this macro is specially crafted for the dlmalloc implementation, it
does not always work for simple malloc.

For example, when allocating 16 bytes via simple malloc, only the first
12 bytes get zeroed out. The last 4 bytes will remain untouched.

This is a problem for DM drivers that are allocated before relocation:
memory allocated via 'platdata_auto_alloc_size' might not be set to
zero, resulting in bogus behaviour.

To fix this, use 'memset' instead of 'MALLOC_ZERO' to zero out memory
that compes from simple malloc.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

As SPL_SPI_FLASH_SUPPORT cannot work without SPL_SPI_SUPPORT, fix
dependencies to prevent enabling SPI flash support without basic SPI
support.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>

Newer versions of LLVM-7 will provide an unused function warning over
console_doenv() in the case of SYS_CONSOLE_IS_IN_ENV not being enabled
as can be the case in SPL.  Add guards around this function.

Signed-off-by: Tom Rini <trini@konsulko.com>

- DFU updates
- USB Storage updates