u-boot.git/configs/Bananapi_defconfig, branch v2019.10

Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig

2019-08-02T15:19:14Z

This converts the following to Kconfig: CONFIG_USE_PREBOOT CONFIG_PREBOOT Both are together in one commit, since otherwise the former causes kconfig to define the latter, which gives duplicate symbol errors. Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the backslash lands in the wrong place. Similarly with socfpga_vining_fpga. Signed-off-by: Simon Glass

sunxi: move CONFIG_SPL_TEXT_BASE from *_defconfig to Kconfig

2019-07-15T06:55:32Z

The choice of the SPL_TEXT_BASE is not really a decision that should be specified by each board's defconfig, as this setting is actually dictated by the SoC's memory map and the BootROM behaviour. To make this obvious and reduce the clutter in the defconfig files, let's specify the SoC constraints in the Kconfig stanza. This allows us to remove these lines from the defconfig files again. Signed-off-by: Andre Przywara Acked-by: Maxime Ripard Reviewed-by: Jagan Teki

configs: move CONFIG_SPL_TEXT_BASE to Kconfig

2019-04-30T01:41:40Z

Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: Simon Goldschmidt [trini: Re-run migration] Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2019-04-30T01:41:40Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2019-02-07T19:53:03Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

sunxi: usb: Switch to Generic host controllers

2019-01-18T16:49:09Z

Onc of key blocker for using USB Generic host controller drivers in Allwinner are CLK and RESET drivers, now these available for USB usage. So switch sunxi USB use EHCI and OHCI Generic controllers. Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD where it already have USB_EHCI_HCD Signed-off-by: Jagan Teki Acked-by: Maxime Ripard

configs: Resync with savedefconfig

2018-09-03T19:26:12Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Convert CONFIG_MII et al to Kconfig

2018-08-17T17:03:54Z

This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford Acked-by: Jagan Teki Acked-by: Joe Hershberger

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02Z

We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini

part: Disable CONFIG_SPL_ISO_PARTITION by default

2018-04-16T22:45:35Z

We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot could load distro images that usually get shipped as iso images. These images usually come with a board agnostic boot environment. However, there is very little point in having ISO support enabled (for anyone really) in SPL, as the whole idea of SPL is to load U-Boot proper which again is board specific. So the fact that we enable ISO support in U-Boot proper does not mean at all that we want ISO support in U-Boot SPL. Hence, let's remove the Kconfig dependency. Along the way, let's also clean up all those default configs that disabled SPL ISO support. Signed-off-by: Alexander Graf