u-boot.git/configs/CHIP_defconfig, branch v2018.09

configs: Resync with savedefconfig

2018-09-03T19:26:12Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02Z

We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini

part: Disable CONFIG_SPL_ISO_PARTITION by default

2018-04-16T22:45:35Z

We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot could load distro images that usually get shipped as iso images. These images usually come with a board agnostic boot environment. However, there is very little point in having ISO support enabled (for anyone really) in SPL, as the whole idea of SPL is to load U-Boot proper which again is board specific. So the fact that we enable ISO support in U-Boot proper does not mean at all that we want ISO support in U-Boot SPL. Hence, let's remove the Kconfig dependency. Along the way, let's also clean up all those default configs that disabled SPL ISO support. Signed-off-by: Alexander Graf

configs: Resync with savedefconfig

2018-04-08T00:37:13Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Convert all of CONFIG_CONS_INDEX to Kconfig

2018-03-16T14:28:52Z

This converts the following to Kconfig: CONFIG_CONS_INDEX We have existing entries for this option in a number of places, with different guards on them. They're also sometimes used for things not directly inside of the serial driver. First, introduce a new symbol to guard the use of CONFIG_CONS_INDEX, so that in the case where we don't need this for the serial driver, but for some other use, we can still do it. Next, consolidate all of these into the single entry in drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that we can imply a correct value here to make the defconfig side of this smaller. Signed-off-by: Adam Ford [trini: Rework a lot of the logic here, such that I took authorship from Adam, but kept his S-o-B line] Signed-off-by: Tom Rini

sunxi: move CONFIG_SYS_TEXT_BASE out of defconfigs

2018-03-14T05:15:37Z

Commit 278b90ce786f ("configs: Migrate CONFIG_SYS_TEXT_BASE") made CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence of moving the common definition shared by almost every sunxi board into 123 individual defconfig files. But the U-Boot start address for Allwinner boards is a platform decision which has been around for ages, so defining it in each *board* config file seems a bit over the top. Define the standard values (160MB into DRAM for most SoCs, with two SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from the individual defconfigs. Signed-off-by: Andre Przywara Acked-by: Maxime Ripard Reviewed-by: Jagan Teki

configs: Migrate CONFIG_SYS_TEXT_BASE

2018-02-11T14:30:09Z

On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2018-02-11T01:29:02Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

sunxi: imply CONFIG_OF_LIBFDT_OVERLAY

2018-01-26T14:32:33Z

fdt overlay support is useful for all sunxi boards, enable per default and remove it from sunxi defconfigs. Signed-off-by: Andre Heider Signed-off-by: Maxime Ripard Reviewed-by: Jagan Teki

configs: sunxi: Drop FASTBOOT_FLASH

2017-12-19T10:56:21Z

Now FASTBOOT_FLASH is auto select for sunxi platform, so drop explicit addition. Signed-off-by: Jagan Teki Acked-by: Maxime Ripard