u-boot.git/configs/Colombus_defconfig, branch master

configs: Resync with savedefconfig

2026-01-06T15:13:29+00:00

Resync all defconfig files using qconfig.py

Signed-off-by: Tom Rini

sunxi: Remove obsolete USBx_VBUS_PIN Kconfig symbols

2025-04-28T18:45:43+00:00

Now that the USB PHY driver uses the device tree to get VBUS supply
regulators, these Kconfig symbols are unused. Remove them.

Signed-off-by: Samuel Holland 
Signed-off-by: Andre Przywara 
Acked-by: Jernej Skrabec

sunxi: define SYS_MONITOR_LEN in Kconfig, not _defconfig

2022-12-13T20:33:31+00:00

Commit 08574ed339fb ("Convert CONFIG_SYS_MONITOR_LEN to Kconfig") moved
the definition of said config variable from the common sunxi header to
*every board's* defconfig.
This is a platform choice, not board specific, so remove the variable
from there, instead set the one value for all Allwinner boards in
Kconfig.

Signed-off-by: Andre Przywara 
Acked-by: Jernej Skrabec

Convert CONFIG_SYS_MONITOR_LEN to Kconfig

2022-11-10T15:08:55+00:00

This converts the following to Kconfig:
   CONFIG_SYS_MONITOR_LEN

To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.

Signed-off-by: Tom Rini 
Reviewed-by: Simon Glass

sunxi: defconfig: drop redundant definitions

2022-10-18T07:18:41+00:00

When some configuration symbols were converted from header files to
Kconfig, their values were placed into *every* defconfig file.
Since we now have sensible per-SoC defaults defined in Kconfig, those
values are now redundant, and can just be removed.
This affects CONFIG_SPL_STACK, CONFIG_SYS_PBSIZE, CONFIG_SPL_MAX_SIZE,
and CONFIG_SYS_BOOTM_LEN.

Signed-off-by: Andre Przywara

Convert CONFIG_SPL_STACK to Kconfig

2022-06-06T16:09:27+00:00

This converts the following to Kconfig:
   CONFIG_SPL_STACK

Signed-off-by: Tom Rini

Convert CONFIG_SYS_PBSIZE to Kconfig

2022-06-06T16:09:00+00:00

This converts the following to Kconfig:
   CONFIG_SYS_PBSIZE

Signed-off-by: Tom Rini

sunxi: video: Convert panel I2C to use DM_I2C

2021-10-12T10:01:17+00:00

Two displays supported by the sunxi display driver (each one used by a
single board) require initialization over I2C. Both previously used
i2c_soft; replace this with the i2c-gpio instance that already exists in
those boards' device trees (sun5i-a13-utoo-p66 and sun6i-a31-colombus).

Since the i2c-gpio nodes are not referenced by any other node in the
device trees (the device trees have no panel node), the I2C bus is
selected by its node name.

This panel initialization code was the only i2c_soft user, so the
i2c_soft GPIO setup code can be removed now as well.

Reviewed-by: Heiko Schocher 
Signed-off-by: Samuel Holland 
Signed-off-by: Andre Przywara

Convert CONFIG_SYS_I2C_SPEED et al to Kconfig

2021-08-30T18:10:07+00:00

This converts the following to Kconfig:
   CONFIG_SYS_I2C_SPEED
   CONFIG_SYS_I2C_SLAVE

Signed-off-by: Tom Rini

Convert CONFIG_SYS_I2C_LEGACY to Kconfig and add CONFIG_[ST]PL_SYS_I2C_LEGACY

2021-08-30T18:10:07+00:00

First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig.  Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL.  Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support.  Convert all of the existing users to
one or more symbols.

Signed-off-by: Tom Rini