u-boot.git/configs/Cyrus_P5040_defconfig, branch master

ppc: Remove Cyrus_P5020 and P5040 boards

2021-04-10T12:05:07Z

These boards have not been converted to CONFIG_DM_MMC by the deadline. Remove them. As the P5020 is the last ARCH_P5020 platform, remove that support as well. Cc: Andy Fleming Cc: Priyanka Jain Signed-off-by: Tom Rini Reviewed-by: Priyanka Jain

Convert CONFIG_ENV_OVERWRITE to Kconfig

2020-07-28T20:18:06Z

This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini

powerpc: move ADDR_MAP to Kconfig

2020-07-10T18:10:43Z

Move ADDR_MAP related config options from include/configs/*.h to the proper place in lib/Kconfig. This has been done using ./tools/moveconfig.py and manual inspection of the generated changes. This is a preparation to use ADDR_MAP helper on ARM 32bit Raspberry Pi4 board for mapping the PCIe XHCI MMIO, which is above the 4GiB identity mapping limit. Signed-off-by: Marek Szyprowski Reviewed-by: Tom Rini

configs: Resync with savedefconfig

2019-12-04T22:18:38Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

env: Finish migration of common ENV options

2019-11-20T23:32:09Z

- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk Cc: Joe Hershberger Cc: Patrick Delaunay Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini Acked-by: Joe Hershberger Reviewed-by: Simon Goldschmidt

env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol

2019-11-20T17:24:50Z

Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk Cc: Joe Hershberger Signed-off-by: Tom Rini

configs: Migrate CONFIG_FMAN_ENET and some related options to Kconfig

2019-05-26T18:40:50Z

Move the main symbol for Freescale Fman Ethernet controller option to Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and rename the SPIFLASH one to follow the same format as all of the others. To do this fully we need to migrate CONFIG_QC, do so. Signed-off-by: Tom Rini

Convert CONFIG_MII et al to Kconfig

2018-08-17T17:03:54Z

This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford Acked-by: Jagan Teki Acked-by: Joe Hershberger

cmd: Kconfig: Move CONFIG_MP to Kconfig

2018-07-10T20:55:59Z

This patch moves CONFIG_MP to Kconfig Signed-off-by: Siva Durga Prasad Paladugu Signed-off-by: Michal Simek

Convert CONFIG_SPI to Kconfig

2018-04-27T18:54:11Z

This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford Signed-off-by: Tom Rini