u-boot.git/configs/M5485CFE_defconfig, branch master

m68k: Remove M5485 boards

2021-07-07T23:52:08Z

These board has not been converted to CONFIG_DM_PCI by the deadline. Remove them. As this is all of the CONFIG_M548x platforms as well, remove that code. Cc: TsiChung Liew Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2021-06-28T14:17:29Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2020-07-28T12:46:52Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2020-01-22T18:38:00Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

configs: add eth dm support for all ColdFire boards

2020-01-10T15:25:09Z

Add dm eth config options for all involved ColdFire-based boards. Signed-off-by: Angelo Durgehello

env: Finish migration of common ENV options

2019-11-20T23:32:09Z

- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk Cc: Joe Hershberger Cc: Patrick Delaunay Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini Acked-by: Joe Hershberger Reviewed-by: Simon Goldschmidt

configs: Resync with savedefconfig

2019-05-26T18:45:25Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

configs: enable use of DT for all m68k boards

2019-05-24T12:11:57Z

Enable DT usage for all m68k boards. To provide a working single binary, the dts has been kept as embedded. Signed-off-by: Angelo Dureghello

Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig

2018-10-19T23:19:50Z

This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford [trini: Re-migrate] Signed-off-by: Tom Rini

Convert CONFIG_MII et al to Kconfig

2018-08-17T17:03:54Z

This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford Acked-by: Jagan Teki Acked-by: Joe Hershberger