u-boot.git/configs/P5020DS_defconfig, branch master

board/freescale: Remove P5020DS board support

2020-09-24T12:27:44Z

Remove NXP powerpc P5020DS board support as it is no longer maintained. Signed-off-by: Priyanka Jain

Convert CONFIG_ENV_OVERWRITE to Kconfig

2020-07-28T20:18:06Z

This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini

powerpc: move ADDR_MAP to Kconfig

2020-07-10T18:10:43Z

Move ADDR_MAP related config options from include/configs/*.h to the proper place in lib/Kconfig. This has been done using ./tools/moveconfig.py and manual inspection of the generated changes. This is a preparation to use ADDR_MAP helper on ARM 32bit Raspberry Pi4 board for mapping the PCIe XHCI MMIO, which is above the 4GiB identity mapping limit. Signed-off-by: Marek Szyprowski Reviewed-by: Tom Rini

Convert CONFIG_PHYLIB et al to Kconfig

2020-04-28T19:57:58Z

This converts the following to Kconfig: CONFIG_PHYLIB CONFIG_BITBANGMII CONFIG_MV88E6352_SWITCH CONFIG_MV88E61XX_SWITCH CONFIG_PHYLIB_10G CONFIG_PHY_AQUANTIA CONFIG_PHY_ATHEROS CONFIG_PHY_BROADCOM CONFIG_PHY_CORTINA CONFIG_PHY_DAVICOM CONFIG_PHY_ET1011C CONFIG_PHY_LXT CONFIG_PHY_MARVELL CONFIG_PHY_MICREL CONFIG_PHY_NATSEMI CONFIG_PHY_REALTEK CONFIG_RTL8211X_PHY_FORCE_MASTER CONFIG_PHY_SMSC CONFIG_PHY_TERANETICS CONFIG_PHY_TI CONFIG_PHY_VITESSE CONFIG_PHY_XILINX Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2019-12-04T22:18:38Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

mtd: ensure MTD/the raw NAND core are compiled when there is a NAND flash

2019-12-04T18:26:17Z

Both symbols must be enabled when there is a raw NAND driver selected. Also enable them when CONFIG_CMD_NAND is selected to avoid breaking things when we'll further rework the MTD dependency description. Signed-off-by: Miquel Raynal Reviewed-by: Boris Brezillon [trini: Rebase and migrate a few more boards here] Signed-off-by: Tom Rini

env: Finish migration of common ENV options

2019-11-20T23:32:09Z

- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk Cc: Joe Hershberger Cc: Patrick Delaunay Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini Acked-by: Joe Hershberger Reviewed-by: Simon Goldschmidt

configs: Migrate CONFIG_FMAN_ENET and some related options to Kconfig

2019-05-26T18:40:50Z

Move the main symbol for Freescale Fman Ethernet controller option to Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and rename the SPIFLASH one to follow the same format as all of the others. To do this fully we need to migrate CONFIG_QC, do so. Signed-off-by: Tom Rini

Convert CONFIG_SF_DEFAULT_* to Kconfig

2019-03-25T21:36:53Z

This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay

Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig

2018-10-19T23:19:50Z

This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford [trini: Re-migrate] Signed-off-by: Tom Rini