These are common for all K3 based boards. Add the common values as
defaults and remove from each board defconfig

Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>

Judith Mendez <jm@ti.com> says:

This patch series fixes MMC_HS_52 mode in am654_sdhci driver,
as well as HIGH_SPEED_ENA and UHS_MODE_SELECT for HS modes.

Also add TI_COMMON_CMD_OPTIONS to K3 Sitara board a53 defconfigs.

Link: https://www.ti.com/lit/er/sprz574a/sprz574a.pdf
Link: https://lore.kernel.org/r/20250417234334.3661321-1-jm@ti.com

Add TI_COMMON_CMD_OPTIONS config options to Sitara K3 boards at
a53 stage since we rely on most of the commands implied for testing
and debugging purposes. Since all commands are now enabled by
default, remove the redundant CMD_* options in the a53 defconfigs.

Also add MMC_REG & MMC_SPEED_MODE_SET useful commands to
TI_COMMON_CMD_OPTIONS.

Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>

SPL_TEXT_BASE is used as the load address for the main domain SPL on k3
platforms.

Since the config value is the same for every board, this patch sets the
value 0x80080000 as default for all 64-bit ARCH_K3, 0x43c00000 as
default for the R5 cores and deletes the instances of SPL_TEXT_BASE in
individual defconfigs.

Signed-off-by: Anshul Dalal <anshuld@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Siddharth Vadapalli <s-vadapalli@ti.com> says:

This series enables USB DFU and USB Mass Storage functionality for
AM62, AM62-LP, AM62A, AM62P and J722S SoCs.

Link: https://lore.kernel.org/r/20250210112239.2639009-1-s-vadapalli@ti.com

The config fragment "am62x_a53_usbdfu.config" which adds USB DFU support
for AM62x SoC is applicable to the AM62Ax SoC as well. Hence, include it
in "am62ax_evm_a53_defconfig" in order to enable support for USB DFU flash
and boot.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>

Judith Mendez <jm@ti.com> says:

Some K3 devices like am62x and am64x have a M4 processor in the MCU
voltage domain. This patch series introduces remoteproc M4 driver which
will be used to load firmware into and start the M4 remote core.

This series also adds support for R5F cores on am64x SoCs in patch 2 and
sets up environment to load FW in remote cores in patch 3,4,5.

This patch series also enables remoteproc drivers by default as per what
remoteproc sybsystem is supported per SoC, thus all remoteproc options
are now deleted in configs/* since they are no longer required.

This patch series was tested on am64x EVM, am62x SK, am62ax SK,
am62px SK boards.

Any additional tested by's are welcome since I was not able to
test any additional boards.

Tested by running the following commands in u-boot prompt:

=> setenv dorprocboot 1
=> run boot_rprocs

Link: https://lore.kernel.org/r/20250210202944.1071931-1-jm@ti.com

Now that remoteproc configs are enabled by default in Kconfig
files, remove these configs which are no longer needed to be
defined here in configs/.

Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>

Santhosh Kumar K <s-k6@ti.com> says:

Hello,

This series adds support for Inline ECC in DDR for AM64X, AM62X,
AM62AX, AM62PX, J721E, J721S2, J722S and J784S4 devices.

Test Results: https://gist.github.com/santhosh21/88de920771ed2efa0463a5a367cb8d7b

Link: https://lore.kernel.org/r/20250106090708.1541212-1-s-k6@ti.com

Set CONFIG_NR_DRAM_BANKS to 2 as we have two banks described in the
memory/ node for lower and higher addressible DDR regions.

This allows use of FDT functions from fdt_support.c to set up and fix up
the memory/ node correctly.

Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Santhosh Kumar K <s-k6@ti.com>