u-boot.git/configs/devkit3250_defconfig, branch v2018.09

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02+00:00

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini

Convert CONFIG_NAND_LPC32XX_SLC to Kconfig

2018-07-22T02:26:25+00:00

This converts the following to Kconfig:
   CONFIG_NAND_LPC32XX_SLC

Signed-off-by: Adam Ford

configs: Resync with savedefconfig

2018-06-04T15:57:37+00:00

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini

Convert CONFIG_SPI to Kconfig

2018-04-27T18:54:11+00:00

This converts the following to Kconfig:
   CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver.  For now, just update
the CONFIG tests.  This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.

Signed-off-by: Adam Ford 
Signed-off-by: Tom Rini

net: phy: Don't limit phy addresses by default

2018-04-13T20:56:47+00:00

Some boards expect to find more than one phy while other boards are old
and need to be limited to a specific phy address. Only limit the phy
address for boards that opt in.

Signed-off-by: Joe Hershberger 
Tested-by: Bin Meng 
Acked-by: Neil Armstrong 
Reviewed-by: Philipp Tomsich

configs: Resync with savedefconfig

2018-04-08T00:37:13+00:00

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini

Move CONFIG_PHY_ADDR to Kconfig

2018-03-13T17:06:33+00:00

CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).

Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.

After the implemention, moveconfig was run. The issues are:
	- edb9315a	- CONFIG_PHYLIB is not enabled. Entry is
			  deleted.

	- ds414		- CONFIG_PHYLIB is in incompatible format:
			  { 0x1, 0x0 }. This entry is also deleted.

	- devkit3250	- The PHY_ADDR is in hex format (0x1F).
			  Manually CONFIG_PHY_ADDR=31 is added in
			  the defconfig.

After the changes the suspicious defconfigs passes building.

Signed-off-by: Stefan Mavrodiev 
Acked-by: Maxime Ripard 
[jagan: rebased on master]
Signed-off-by: Jagan Teki 
Reviewed-by: Jagan Teki

spi: Migrate CONFIG_LPC32XX_SSP to Kconfig

2018-02-14T04:01:44+00:00

Signed-off-by: Tuomas Tynkkynen

configs: Migrate CONFIG_SYS_TEXT_BASE

2018-02-11T14:30:09+00:00

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini

cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA

2018-02-06T01:58:11+00:00

cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

 # CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.

Signed-off-by: Tuomas Tynkkynen