u-boot.git/configs/devkit3250_defconfig, branch v2018.11

Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig

2018-10-19T23:19:50Z

This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford [trini: Re-migrate] Signed-off-by: Tom Rini

arm: lpc32xx: add CONFIG_ARCH_LPC32XX build option

2018-10-19T16:56:58Z

The explicit arch specific build symbol allows to group supported boards, generalize common config options and it will serve as a dependency for platform only drivers. Two related board defconfigs are resynced after the change. Signed-off-by: Vladimir Zapolskiy

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02Z

We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini

Convert CONFIG_NAND_LPC32XX_SLC to Kconfig

2018-07-22T02:26:25Z

This converts the following to Kconfig: CONFIG_NAND_LPC32XX_SLC Signed-off-by: Adam Ford

configs: Resync with savedefconfig

2018-06-04T15:57:37Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Convert CONFIG_SPI to Kconfig

2018-04-27T18:54:11Z

This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford Signed-off-by: Tom Rini

net: phy: Don't limit phy addresses by default

2018-04-13T20:56:47Z

Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger Tested-by: Bin Meng Acked-by: Neil Armstrong Reviewed-by: Philipp Tomsich

configs: Resync with savedefconfig

2018-04-08T00:37:13Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Move CONFIG_PHY_ADDR to Kconfig

2018-03-13T17:06:33Z

CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev Acked-by: Maxime Ripard [jagan: rebased on master] Signed-off-by: Jagan Teki Reviewed-by: Jagan Teki

spi: Migrate CONFIG_LPC32XX_SSP to Kconfig

2018-02-14T04:01:44Z

Signed-off-by: Tuomas Tynkkynen